Auto Parts Search
2009 Mercury Sable CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Mercury REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
BRAKE SERVICE PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Anti-Lock Brakes -> MKS, Sable, Taurus & Taurus X -> Description -> ABS Hydraulic Control Unit & Anti-Lock Brake Control Module -> Anti-Lock Brake Sensor -> Brake Master Cylinder -> Power Brake Booster
Vehicle: 2009 Mercury Sable 3.5 V6 GAS
Power Brake Booster
The diaphragm-type power brake booster is a self-contained unit, mounted on the firewall. The booster uses engine intake manifold vacuum and atmospheric pressure for its power. Other than the power brake booster check valve, the booster is serviced only as an assembly. The booster must be replaced if it becomes damaged or inoperative.
Brake Master Cylinder
The brake master cylinder consists of a fluid reservoir, reservoir control valve and a fluid level indicator. The fluid level indicator is located inside the brake master cylinder reservoir and replaces the previo...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2009 Mercury Sable Premier 3.5 V6 GAS
- Remove center hub cap from wheel.
- Loosen hub nut.
- Raise and support vehicle.
- Remove front wheel and tire assembly.
- Remove hub nut and washer.
- Remove front brake anti-lock sensor harness from clip.
- Remove and position front brake anti-lock sensor aside.
- Remove and discard lower ball joint nut.
- Remove lower strut support nut and bolt. Discard nut.
- Using suitable tools, press ball joint stud until it is loose in knuckle.
- Wire knuckle to strut. This will prevent knuckle from falling off of strut while knuckle and lower ball joint are separated. Failure to follow these instructions may ...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Component Replacement -> Installation -> Removal -> TPMS Sensor -> TPMS Sensor Strap & Cradle
Vehicle: 2009 Mercury Sable Premier 3.5 V6 GAS
TPMS Sensor
Removal
Tire pressure sensors are manufactured in multiple colors based on their application. When installing a new sensor, make sure the color of the sensor being installed matches the color of the sensor that was removed. The different colored sensors are not interchangeable, Fig. .
- Loosen the wheel and tire assembly lug nuts.
- Raise and support the vehicle with jack stands.
- Remove the wheel and tire assembly.
- Position the wheel and tire assembly on a suitable tire changing machine as follows:
- On a paddle type tire machine, position the valve step at 12 o'clock or 6 ...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Starter, Replace
Vehicle: 2009 Mercury Sable Premier 3.5 V6 GAS
- Disconnect battery ground cable.
- Remove air cleaner outlet pipe and air cleaner assembly.
- Disconnect transmission shift cable and adjustment lock from transmission manual control lever.
- Disconnect transmission shift cable rotating slide snap and position aside transmission cable.
- Remove nut and transmission manual control lever.
- Remove starter motor terminal cover.
- Remove starter motor solenoid battery cable nut.
- R...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Ford Motor Co. Cars -> Electronic Throttle Control ->
Vehicle: 2009 Mercury Sable Premier 3.5 V6 GAS
Electronic throttle displays when the system has malfunctioned and the engine has defaulted to a limp-home operation. On vehicles equipped with ...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2009 Mercury Sable 3.5 V6 GAS
Inlet
- Drain coolant into a suitable container.
- Loosen hose clamp connecting hose to heater core inlet tube.
- Loosen hose clamp connecting hose to thermostat housing.
- Remove hose from vehicle.
- Reverse procedure to...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2009 Mercury Sable 3.5 V6 GAS
- Rotate belt tensioner clockwise using a suitable belt tension release tool.
- Remove belt from alternator pulley.
- Raise and support vehicle.
- Remove four screws and 6 pin-type retainers, then the righthand fender splash shield.
- Remove accessory drive belt.
- Install a suitable power steering belt removal tool, between power steering pump be...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable SERPENTINE BELT SERVICE PROCEDURES
TECHNICAL SERVICE BULLETINS FOR 2009 Mercury Sable AUTOMOBILES
OEM TSB listings for most 2009 Mercury Sable cars and light trucks sold in the U.S. from 1985+.
Document: 6F50 Transmission With A Moan Or Buzz Type Noise On 4-5 Upshift Or 5-6 Upshift Vehicle: 2009 Mercury Sable 3.5 V6 GAS Symptoms: |
Document: SERVICE TIP - POWER TAKE-OFF UNIT (PTU) - RIGHT HAND INTERMEDIATE SHAFT SEAL LEAKS Vehicle: 2009 Mercury Sable 3.5 V6 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2009 Mercury Sable AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2009 Mercury Sable cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2009 Mercury Sable cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2009 Mercury Sable cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2009 Mercury Sable cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2009 Mercury Sable vehicle. |
Access the Complete guide! |