Auto Parts Search
We have info for following modifications of 2009 Mercury Sable
- 2009 Mercury Sable 3.5 V6 GAS, CC:3496, CID:213, Fuel Injection, Aspiration:213, Engine VIN:, Desg:W
- 2009 Mercury Sable Premier 3.5 V6 GAS, CC:3496, CID:213, Fuel Injection, Aspiration:213, Engine VIN:, Desg:W
BRAKE SERVICE PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2009 Mercury Sable cars and light trucks from 1990+.
Disc Brakes -> Rear Disc & Parking Brakes -> Parking Brake Service -> Crown Victoria, Grand Marquis & Town Car -> Parking Brake Linings, Replace
Vehicle: 2009 Mercury Sable 3.5 V6 GAS
Parking Brake Linings, Replace
Crown Victoria, Grand Marquis & Town Car
- Remove tire and wheel assembly.
- Remove brake rotor.
- Remove spring and brake shoe adjusting screw.
- Remove brake shoe hold down springs.
- Remove parking bake shoe and linings.
- Reverse procedure to install noting the following:
- Lubricate bra...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2009 Mercury Sable cars and light trucks from 1990+.
Hydraulic Brake Systems -> Hydraulic Brake System Flush
Vehicle: 2009 Mercury Sable Premier 3.5 V6 GAS
Whenever new brake components are installed in the hydraulic system, it is recommended that the entire hydraulic system be thoroughly flushed with clean brake fluid.
It may sometime become required to flush out the system due to the presence of mineral oil, kerosene, gasoline, etc., which will cause swelling of rubber piston cups and valves and render them inoperative.
Flushing is performed at e...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2009 Mercury Sable cars and light trucks from 1990+.
Power Brake Units -> Adjustments -> Bendix System -> Single Diaphragm Booster
Vehicle: 2009 Mercury Sable Premier 3.5 V6 GAS
Bendix System
- Disconnect master cylinder from booster leaving brake lines connected and secure cylinder aside.
- Start engine and operate engine at idle speed.
- With engine running, position gauge over pushrod. Gauge should bottom against booster housing with force of approximately five lbs. applied to pushrod, Fig. . Ensure pushrod is properly seated in booster when performing gauge inspection.
- If force required to seat gauge is more than five lbs., shorten length of pushrod.
- If force required to seat gauge is less than five lbs., lengthen pushrod.
- Install master cylinder and remove reservo...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2009 Mercury Sable cars and light trucks from 1990+.
Disc Brakes -> Front Disc Brakes -> Tightening Specifications
Vehicle: 2009 Mercury Sable 3.5 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2009 Mercury Sable cars and light trucks from 1990+.
Disc Brakes -> Rear Disc & Parking Brakes -> Brake System Bleed -> System Priming -> Wheel Bleeding Sequence
Vehicle: 2009 Mercury Sable 3.5 V6 GAS
Pressure bleeding is recommended for all hydraulic disc brake systems.
Do not use brake fluid drained from the hydraulic system when bleeding the brakes. Ensure disc brake pistons are returned to their normal positions and the shoe and lining assemblies are properly seated. Before driving the vehicle, inspect the brake operation.
Do not shake the pressure bleeder tank while air is being added or after it has been pressurized. This will prevent air from the tank getting into the lines. Set the tank in the required location, then bring the air hose to the tank. Do not move the ta...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2009 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2009 Mercury Sable cars and light trucks from 1990+.
Anti-Lock Brakes -> MKS, Sable, Taurus & Taurus X -> Precautions -> Hydraulic Brake Fluid Color
Vehicle: 2009 Mercury Sable Premier 3.5 V6 GAS
Hydraulic Brake Fluid Color
Hydraulic brake fluid must conform with the requirements of Federal Motor Vehicle Safety Standard 116. Under this standard, brake fluids are visually different from other automotive fluids such as transmission, power steering and engine.
Fluid color in a normal brake system may vary from its original color for many reasons. A brake master cylinder may show significantly different shades fluid color between the two brake master cylinder reservoirs. Color may also appear to vary between cast steel and die cast aluminum reservoirs. Some reasons for discolorati...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Sable BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2009 Mercury Sable vehicle. |
Access the Complete guide! |