Auto Parts Search
We have info for following modifications of 2008 Ford Explorer Sport Trac
- 2008 Ford Explorer Sport Trac XLT 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:8
- 2008 Ford Explorer Sport Trac XLT 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:K
- 2008 Ford Explorer Sport Trac Limited 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:8
- 2008 Ford Explorer Sport Trac Limited 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:K
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Ford Explorer Sport Trac AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Ford Explorer Sport Trac cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2008 Ford Explorer Sport Trac Limited 4.0 V6 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Explorer Sport Trac DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Ford Explorer Sport Trac AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Ford Explorer Sport Trac cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2008 Ford Explorer Sport Trac XLT 4.0 V6 GAS
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Tighten transfer case flange bolts in a cross pattern.
- Torque flange bolts to 22 ft. lbs.
- Torque U-joint retainer bolts to 26 ft. lbs.
Rear
One P...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Explorer Sport Trac DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Ford Explorer Sport Trac AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Ford Explorer Sport Trac cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2008 Ford Explorer Sport Trac Limited 4.0 V6 GAS
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Tighten transfer case flange bolts in a cross pattern.
- Torque flange bolts to 22 ft. lbs.
- Torque U-joint retainer bolts to 26 ft. lbs.
Rear
One P...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Explorer Sport Trac DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Ford Explorer Sport Trac AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Ford Explorer Sport Trac cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2008 Ford Explorer Sport Trac XLT 4.0 V6 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Explorer Sport Trac DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Ford Explorer Sport Trac AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Ford Explorer Sport Trac cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2008 Ford Explorer Sport Trac XLT 4.6 V8 GAS
Front
- Loosen the front axle wheel hub retainer.
- With the vehicle in NEUTRAL, position on a hoist.
- Remove the front wheel and tire assembly.
- Remove rear disc brake caliper and suspend aside using mechanics wire.
- Remove front axle wheel hub retaining nut.
- Remove tie rod end nut and separate tie rod end from knuckle.
- Remove stabilizer bar link nut.
- Remove upper ball joint nut and separate upper ball joint from knuckle.
- Remove CV shaft assembly from vehicle.
- Reverse procedure to install, noting the following:
- Torque axle shaft hub nut to 184 ft. lbs.
- Torque upper ball joint nut to 51 ft....
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Explorer Sport Trac DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Ford Explorer Sport Trac AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Ford Explorer Sport Trac cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2008 Ford Explorer Sport Trac XLT 4.0 V6 GAS
Front
- Loosen the front axle wheel hub retainer.
- With the vehicle in NEUTRAL, position on a hoist.
- Remove the front wheel and tire assembly.
- Remove rear disc brake caliper and suspend aside using mechanics wire.
- Remove front axle wheel hub retaining nut.
- Remove tie rod end nut and separate tie rod end from knuckle.
- Remove stabilizer bar link nut.
- Remove upper ball joint nut and separate upper ball joint from knuckle.
- Remove CV shaft assembly from vehicle.
- Reverse procedure to install, noting the following:
- Torque axle shaft hub nut to 184 ft. lbs.
- Torque upper ball joint nut to 51 ft....
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Explorer Sport Trac DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Ford Explorer Sport Trac vehicle. |
Access the Complete guide! |