Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 Land Rover Range Rover Sport car and truck
repair procedures including Land Rover engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2009 Land Rover Range Rover Sport automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2009 Land Rover Range Rover Sport
- 2009 Land Rover Range Rover Sport HSE 4.4 V8 GAS, CC:4394, Fuel Injection, Engine VIN:, Desg:5
- 2009 Land Rover Range Rover Sport Supercharged 4.2 V8 GAS, CC:4196, Fuel Injection, Engine VIN:, Desg:3
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Land Rover Range Rover Sport AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Land Rover Range Rover Sport cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Install -> Rear -> Remove
Vehicle: 2009 Land Rover Range Rover Sport HSE 4.4 V8 GAS
Front
It is possible to fit the driveshaft incorrectly. Note the orientation before removal.
A small amount of oil may weep from the driveshaft joints during storage. The loss of this oil will not affect the operation or durability of the joint.
Remove
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove exhaust system.
- Mark position of driveshaft flange in relation to drive pinion flange.
- Remove six Torx bolts and washers at transfer case drive flange, discard bolts.
- Release driveshaft from transfer case drive flange. To avoid damage to joint or gaiter, do not allow dr...
CLICK HERE TO GET FULL ACCESS TO 2009 Land Rover Range Rover Sport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Land Rover Range Rover Sport AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Land Rover Range Rover Sport cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Install -> Rear -> Remove
Vehicle: 2009 Land Rover Range Rover Sport HSE 4.4 V8 GAS
Front
Remove
- Raise and support front of vehicle.
- Drain differential lubricant.
- Remove wheel and tire assembly.
- Remove and discard driveshaft retaining nut.
- Remove and discard stabilizer bar link nuts. Use a wrench on hexagon provided to prevent ball joint from rotating.
- Remove bolt and brake hose bracket from wheel knuckle.
- Loosen tie-rod end ball joint retaining nut. Ensure the ball joint seal is not damaged. A damaged seal will lead to the premature failure of the joint.
- Release tie-rod end ball joint from wheel knuckle, using ball joint separator tool No. LRT-54-027 or equivale...
CLICK HERE TO GET FULL ACCESS TO 2009 Land Rover Range Rover Sport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Land Rover Range Rover Sport AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Land Rover Range Rover Sport cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Install -> Rear -> Remove
Vehicle: 2009 Land Rover Range Rover Sport Supercharged 4.2 V8 GAS
Front
It is possible to fit the driveshaft incorrectly. Note the orientation before removal.
A small amount of oil may weep from the driveshaft joints during storage. The loss of this oil will not affect the operation or durability of the joint.
Remove
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove exhaust system.
- Mark position of driveshaft flange in relation to drive pinion flange.
- Remove six Torx bolts and washers at transfer case drive flange, discard bolts.
- Release driveshaft from transfer case drive flange. To avoid damage to joint or gaiter, do not allow dr...
CLICK HERE TO GET FULL ACCESS TO 2009 Land Rover Range Rover Sport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Land Rover Range Rover Sport AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Land Rover Range Rover Sport cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Install -> Rear -> Remove
Vehicle: 2009 Land Rover Range Rover Sport Supercharged 4.2 V8 GAS
Front
Remove
- Raise and support front of vehicle.
- Drain differential lubricant.
- Remove wheel and tire assembly.
- Remove and discard driveshaft retaining nut.
- Remove and discard stabilizer bar link nuts. Use a wrench on hexagon provided to prevent ball joint from rotating.
- Remove bolt and brake hose bracket from wheel knuckle.
- Loosen tie-rod end ball joint retaining nut. Ensure the ball joint seal is not damaged. A damaged seal will lead to the premature failure of the joint.
- Release tie-rod end ball joint from wheel knuckle, using ball joint separator tool No. LRT-54-027 or equivale...
CLICK HERE TO GET FULL ACCESS TO 2009 Land Rover Range Rover Sport DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2009 Land Rover Range Rover Sport vehicle.
|
| Access the Complete guide! |
