Auto Parts Search
We have info for following modifications of 2008 Chevrolet Colorado
- 2008 Chevrolet Colorado LT 3.7 L5 GAS, CC:3654, CID:223, Fuel Injection, Aspiration:223, Engine VIN:, Desg:E
- 2008 Chevrolet Colorado LT 2.9 L4 GAS, CC:2921, CID:178, Fuel Injection, Aspiration:178, Engine VIN:, Desg:9
- 2008 Chevrolet Colorado LS 3.7 L5 GAS, CC:3654, CID:223, Fuel Injection, Aspiration:223, Engine VIN:, Desg:E
- 2008 Chevrolet Colorado LS 2.9 L4 GAS, CC:2921, CID:178, Fuel Injection, Aspiration:178, Engine VIN:, Desg:9
- 2008 Chevrolet Colorado WT 3.7 L5 GAS, CC:3654, CID:223, Fuel Injection, Aspiration:223, Engine VIN:, Desg:E
- 2008 Chevrolet Colorado WT 2.9 L4 GAS, CC:2921, CID:178, Fuel Injection, Aspiration:178, Engine VIN:, Desg:9
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Chevrolet Colorado AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Chevrolet Colorado cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 Chevrolet Colorado LT 2.9 L4 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove wheel drive shaft nut and washer. Do not reuse wheel drive shaft nut, replace with new.
- Remove steering knuckle assembly.
- Release wheel drive shaft by placing a brass drift against tripod housing. Firmly strike brass drift with a hammer to release drive shaft.
- Remove front wheel drive shaft from vehicle.
- Reverse procedure to install, noting the following:
- A snap or po...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Colorado DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Chevrolet Colorado AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Chevrolet Colorado cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Two Piece Driveshaft
Vehicle: 2008 Chevrolet Colorado LS 2.9 L4 GAS
Front
- Raise and support vehicle.
- Mark the front U-joint to the pinion yoke on the front differential.
- Mark the relationship of the rear U-joint to the transfer case drive flange.
- Remove the retaining nuts and bolts from the drive flange.
- Remove the clamps and retaining bolts from the front drive axle pinion flange.
- Remove the front propeller shaft from the vehicle.
- Using tape and or a rubber band, wrap the front U-joint bearing caps to ensure the caps do not separate from the U-joint.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft to the pinion flang...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Colorado DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Chevrolet Colorado AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Chevrolet Colorado cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Two Piece Driveshaft
Vehicle: 2008 Chevrolet Colorado WT 3.7 L5 GAS
Front
- Raise and support vehicle.
- Mark the front U-joint to the pinion yoke on the front differential.
- Mark the relationship of the rear U-joint to the transfer case drive flange.
- Remove the retaining nuts and bolts from the drive flange.
- Remove the clamps and retaining bolts from the front drive axle pinion flange.
- Remove the front propeller shaft from the vehicle.
- Using tape and or a rubber band, wrap the front U-joint bearing caps to ensure the caps do not separate from the U-joint.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft to the pinion flang...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Colorado DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Chevrolet Colorado AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Chevrolet Colorado cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 Chevrolet Colorado WT 3.7 L5 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove wheel drive shaft nut and washer. Do not reuse wheel drive shaft nut, replace with new.
- Remove steering knuckle assembly.
- Release wheel drive shaft by placing a brass drift against tripod housing. Firmly strike brass drift with a hammer to release drive shaft.
- Remove front wheel drive shaft from vehicle.
- Reverse procedure to install, noting the following:
- A snap or po...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Colorado DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Chevrolet Colorado AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Chevrolet Colorado cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2008 Chevrolet Colorado LT 2.9 L4 GAS
Never clamp propeller shaft tubing in a vise. Clamping could dent or deform the tube causing an imbalance or unsafe condition. Always clamp on one of the yokes and support the shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage the bushing or cut the lip seal.
Disassemble
- Support propeller shaft in a line horizontal with table of a press.
- Mark propeller shaft in order to show which end connects to transmission and which end goes to rear axle.
- On models equipped with external snap ring retainers, proceed as follows:
- Disassemble snap rings by ...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Colorado DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Chevrolet Colorado AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Chevrolet Colorado cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Two Piece Driveshaft
Vehicle: 2008 Chevrolet Colorado LT 2.9 L4 GAS
Front
- Raise and support vehicle.
- Mark the front U-joint to the pinion yoke on the front differential.
- Mark the relationship of the rear U-joint to the transfer case drive flange.
- Remove the retaining nuts and bolts from the drive flange.
- Remove the clamps and retaining bolts from the front drive axle pinion flange.
- Remove the front propeller shaft from the vehicle.
- Using tape and or a rubber band, wrap the front U-joint bearing caps to ensure the caps do not separate from the U-joint.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft to the pinion flang...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Colorado DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Chevrolet Colorado vehicle. |
Access the Complete guide! |