Auto Parts Search
We have info for following modifications of 2007 Ford Expedition
- 2007 Ford Expedition XLT 5.4 V8 GAS, CID:330, Fuel Injection, Aspiration:330, Engine VIN:, Desg:5
- 2007 Ford Expedition Limited 5.4 V8 GAS, CID:330, Fuel Injection, Aspiration:330, Engine VIN:, Desg:5
- 2007 Ford Expedition Eddie Bauer 5.4 V8 GAS, CID:330, Fuel Injection, Aspiration:330, Engine VIN:, Desg:5
- 2007 Ford Expedition EL XLT 5.4 V8 GAS, CID:330, Fuel Injection, Aspiration:330, Engine VIN:, Desg:5
- 2007 Ford Expedition EL Limited 5.4 V8 GAS, CID:330, Fuel Injection, Aspiration:330, Engine VIN:, Desg:5
- 2007 Ford Expedition EL Eddie Bauer 5.4 V8 GAS, CID:330, Fuel Injection, Aspiration:330, Engine VIN:, Desg:5
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Expedition AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Expedition cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2007 Ford Expedition EL Limited 5.4 V8 GAS
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard four flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Torque flange bolts to 82 ft. lbs.
- Torque U-joint retainer bolts to 26 ft. lbs.
Rear
One Piece Driveshaft
- Raise and support vehicle.
- To maint...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Expedition DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Expedition AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Expedition cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2007 Ford Expedition XLT 5.4 V8 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Expedition DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Expedition AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Expedition cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2007 Ford Expedition Limited 5.4 V8 GAS
Front
- With vehicle in NEUTRAL, position on a hoist.
- Remove the front wheel and tire assembly.
- Remove dust cap and nut from axle halfshaft.
- Remove upper ball joint nut and separate ball joint from steering knuckle.
- Remove wheel end retaining bolts from CV shaft.
- Remove CV shaft flange retaining bolts.
- Remove CV shaft f...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Expedition DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Expedition AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Expedition cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2007 Ford Expedition Limited 5.4 V8 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Expedition DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Expedition AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Expedition cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2007 Ford Expedition EL Eddie Bauer 5.4 V8 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Expedition DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Expedition AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Expedition cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2007 Ford Expedition Eddie Bauer 5.4 V8 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Expedition DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2007 Ford Expedition vehicle. |
Access the Complete guide! |