Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Toyota Sienna car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 Toyota Sienna automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 Toyota Sienna
- 2008 Toyota Sienna CE 3.5 V6 GAS, CC:3456, Fuel Injection
- 2008 Toyota Sienna LE 3.5 V6 GAS, CC:3456, Fuel Injection
- 2008 Toyota Sienna XLE 3.5 V6 GAS, CC:3456, Fuel Injection
- 2008 Toyota Sienna Limited 3.5 V6 GAS, CC:3456, Fuel Injection
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sienna AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sienna cars and light trucks sold in the U.S. from mid 1990's+.
Description
Vehicle: 2008 Toyota Sienna XLE 3.5 V6 GAS
If the TPMS (Tire Pressure Monitor System) warning system detects a drop in the tire inflation pressure while the vehicle is operated, the TPMS ECU (Electronic Control Unit) turns on the low tire pressure warning lamp in the instrument cluster to warn the driver. The...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sienna TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sienna AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sienna cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> TPMS ECU -> TPMS Pressure Warning Valve & Transmitter -> TPMS Receiver
Vehicle: 2008 Toyota Sienna LE 3.5 V6 GAS
TPMS Pressure Warning Valve & Transmitter
If installing a replacement tire pressure warning valve and transmitter, note the identification number for use during registration. Refer to the Registration under the "Relearn Procedures."
Removal
- Loosen the wheel lug nuts.
- Raise and support vehicle with jack stands.
- Remove the wheel and tire assembly.
- Remove the tire valve stem cap, then the valve stem core and allow the tire to deflate, Fig. .
- Remove the nut retaining the tire pressure warning valve and transmitter to the wheel assembly, then drop the transmitter inside the tire.
- Using a...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sienna TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sienna AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sienna cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures -> Initialization -> Registration -> TPMS Pressure Warning Valve & Transmitter
Vehicle: 2008 Toyota Sienna XLE 3.5 V6 GAS
Initialization
- Ensure tires are inflated to the specified pressure.
- Place the ignition switch in the On position.
- Press and hold the reset switch for 3 seconds or more until the TPMS warning lamp flashes 3 times and then turns off, indicating the system initialization has begun.
- The ignition switch must be left in the on position for at least 7 minutes for initialization to complete.
- Place the ignition switch in the Off position.
- Connect a suitable scan tool to DLC3 located under left side of instrument panel.
- Place the ignition switch in the On position.
- On scan tool select Tire Pre...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sienna TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sienna AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sienna cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> TPMS ECU -> TPMS Pressure Warning Valve & Transmitter -> TPMS Receiver
Vehicle: 2008 Toyota Sienna XLE 3.5 V6 GAS
TPMS Pressure Warning Valve & Transmitter
If installing a replacement tire pressure warning valve and transmitter, note the identification number for use during registration. Refer to the Registration under the "Relearn Procedures."
Removal
- Loosen the wheel lug nuts.
- Raise and support vehicle with jack stands.
- Remove the wheel and tire assembly.
- Remove the tire valve stem cap, then the valve stem core and allow the tire to deflate, Fig. .
- Remove the nut retaining the tire pressure warning valve and transmitter to the wheel assembly, then drop the transmitter inside the tire.
- Using a...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sienna TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sienna AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sienna cars and light trucks sold in the U.S. from mid 1990's+.
Description
Vehicle: 2008 Toyota Sienna CE 3.5 V6 GAS
If the TPMS (Tire Pressure Monitor System) warning system detects a drop in the tire inflation pressure while the vehicle is operated, the TPMS ECU (Electronic Control Unit) turns on the low tire pressure warning lamp in the instrument cluster to warn the driver. The...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sienna TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Toyota Sienna AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Toyota Sienna cars and light trucks sold in the U.S. from mid 1990's+.
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2008 Toyota Sienna LE 3.5 V6 GAS
Refer to Fig. for wiring...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sienna TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Toyota Sienna vehicle.
|
| Access the Complete guide! |
