Auto Parts Search
We have info for following modifications of 2008 Toyota Sequoia
- 2008 Toyota Sequoia Limited 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285
- 2008 Toyota Sequoia Limited 5.7 V8 GAS, CC:5663, CID:345, Fuel Injection, Aspiration:345
- 2008 Toyota Sequoia SR5 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285
- 2008 Toyota Sequoia SR5 5.7 V8 GAS, CC:5663, CID:345, Fuel Injection, Aspiration:345
- 2008 Toyota Sequoia Platinum 5.7 V8 GAS, CC:5663, CID:345, Fuel Injection, Aspiration:345
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Toyota Sequoia cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2008 Toyota Sequoia SR5 5.7 V8 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolt...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Toyota Sequoia cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 2008 Toyota Sequoia Limited 4.7 V8 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with ...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Toyota Sequoia cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 2008 Toyota Sequoia SR5 5.7 V8 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with ...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Toyota Sequoia cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2008 Toyota Sequoia SR5 4.7 V8 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolt...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Toyota Sequoia cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2008 Toyota Sequoia Limited 5.7 V8 GAS
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolt...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Toyota Sequoia AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Toyota Sequoia cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 2008 Toyota Sequoia SR5 4.7 V8 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with ...
CLICK HERE TO GET FULL ACCESS TO 2008 Toyota Sequoia DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Toyota Sequoia vehicle. |
Access the Complete guide! |