2008 Mitsubishi Raider Driveline, U-Joint & CV Axles Replacement (ONLINE REPAIR MANUALS)

Auto Parts Search


Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!
Help me findSearch
Get Full Access Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Mitsubishi Raider car and truck repair procedures including Mitsubishi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up & drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix your 2008 Mitsubishi Raider automobile. Try the Automotix DIY solution today!
DIY REPAIR SAMPLES > CONTINUE EXPLORING >

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mitsubishi Raider AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Mitsubishi Raider cars and light trucks from 1990+.

DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2008 Mitsubishi Raider LS 3.7 V6 GAS

Front

  • Place transmission in neutral, and raise and support vehicle.
  • On models equipped with skid plate, remove bolts securing skid plate.
  • On all models, mark front companion flange to front driveline.
  • Mark transfer case companion flange to front driveline.
  • Remove exhaust crossover bolts from exhaust manifolds and lower crossover.
  • Remove driveline shaft flange bolts from pinion flange.
  • Remove driveline bolts from shaft joint.
  • Slide driveline off transfer case and remove shaft. Failure to observe instructions may result in a driveline vibration.
  • Reverse procedure to install, noting th...

CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Raider DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mitsubishi Raider AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Mitsubishi Raider cars and light trucks from 1990+.

CV AXLE SHAFT, Replace
Vehicle: 2008 Mitsubishi Raider LS 3.7 V6 GAS

Do not strike ABS rotors or outer race of driveshaft against other parts when removing or installing driveshaft. Use care not to strike pole piece at tip of front wheel speed sensor with tools when servicing vehicle.

  • Place vehicle in neutral.
  • Raise and support vehicle and support it with safety stands in proper locations.
  • On models equipped with skid plate, remove skid plate bolts.
  • On all models, remove wheel nuts and front wheels.
  • Remove wheel hub cotter pin, nut, and washer. Do not apply pressure to wheel bearing from vehicle weight to avo...

CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Raider DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mitsubishi Raider AUTOMOBILES

Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Mitsubishi Raider cars and light trucks from 1990+.

DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Injected Rings -> Snap Ring Type
Vehicle: 2008 Mitsubishi Raider LS 3.7 V6 GAS

Disassemble

Snap Ring Type

This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped wit companion/slip yoke repeat steps to remove remaining cardan joint.

  • Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
  • Tap outside of bearing cap with a drift to loosen snap ring.
  • Remove snap rings from both sides of yoke using suitable tool.
  • Position yoke with grease fitting pointing up, if equipped.
  • Position socket with a...

CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Raider DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES

Shop online for auto body parts, engines, wheels, lights...

More parts
Help me findSearch
Auto Repair Quick Search
Help me find
Search DIY repair manuals by VIN...
Vehicle Identification Number is a unique serial number used by the automotive industry to identify individual motor vehicles

Find out what info we have for your vehicle

Get the Complete Technical Service Bulletins!
Get the Complete Technical Service Bulletins!Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Mitsubishi Raider vehicle.
Access the Complete guide!
Need To Fix Your Car or Truck?
Save Money With Free Car Insurance Quote
FREE car insurance quote
Enter Zip Code:
Auto Repair Quick Search
Help me find