Auto Parts Search
2008 Ford Edge CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Ford Edge car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Edge automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2008 Ford Edge AUTOMOBILES
Disc Brakes -> Rotor Replace -> E-Series -> Edge & MKX -> Escape & Mariner -> Expedition & Navigator -> Explorer & Mountaineer -> Explorer Sport/Sport Trac -> F-150 & Mark LT -> F-250/350 w/2WD -> F-250/350 w/4WD & F-450/550 -> F-Super Duty & Motorhome -> Freestar & Monterey -> Front -> Installation -> Motorhome -> Ranger -> Rear -> Removal
Vehicle: 2008 Ford Edge SEL 3.5 V6 GAS
Edge & MKX
- Remove disc brake caliper and anchor plate as outlined in .
- Remove rotor
- Reverse Procedure to install. Tighten all nuts and bolts to specification.
Escape & Mariner
- Remove disc brake caliper and anchor plate as outlined in "."
- Remove rotor
- Reverse Procedure to install. Tighten all nuts and bolts to specification.
E-Series
Front
Refer to Figs. through and remove components in sequence listed.
Rear
Removal
- Remove disc brake caliper, refer to .
- Remove axle shafts.
- Lift lock washer tab from slot in outer lock nut, Figs. through .
- Remove outer lock nut using Front Wheel Bearing Spanner too...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Ford Edge AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2008 Ford Edge Limited 3.5 V6 GAS
Index-mark both driveshaft flanges.
- With vehicle in NEUTRAL, position it on a hoist.
- Remove and discard front driveshaft-to-transfer case bolts. Do not reuse constant velocity (CV) joint bolts. Install new bolts or damage to vehicle may occur.
- Remove and discard U-joint flange bolts. Do not reuse bolts for rear U-joint flange or damage to component may occur. Install new bolts.
- With help of an assistant, remove center bearing support nuts and driveshaft.
- Remove and discard universal joint cap strap bolts and cap straps and remove front driveshaft. Do not reuse ...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Ford Edge AUTOMOBILES
Component Locations
Vehicle: 2008 Ford Edge Limited 3.5 V6 GAS
Refer to F...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2008 Ford Edge AUTOMOBILES
Starter, Replace
Vehicle: 2008 Ford Edge SEL 3.5 V6 GAS
Always disconnect battery ground cable at the battery before disconnecting starter motor battery terminal lead. If a tool is shorted at the starter motor battery terminal, the tool can quickly heat enough to cause a skin burn. Failure to follow this instruction may result in serious personal injury.
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove starter motor solenoid terminal cover.A protective cap or boot is provided over battery input terminal on all vehicle lines and must be reinstalled after repair. Failure to follow this instruction may result in dama...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2008 Ford Edge AUTOMOBILES
Cabin Air Filter Service -> Ford Motor Co. -> 2007-09 Edge & MKX
Vehicle: 2008 Ford Edge SEL 3.5 V6 GAS
Under normal operating conditions the cabin air filter should be replaced every 15,000 miles. In dusty areas change the cabin air filter more often.
- Open and then remove glove compartment door.
- Remove cabin ai...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Ford Edge AUTOMOBILES
Ford Motor Co. Trucks -> Electronic Throttle Control ->
Vehicle: 2008 Ford Edge Limited 3.5 V6 GAS
Electronic throttle displays when the system has malfunctioned and the engine has defaulted to a limp-home operation. On vehicles equipped with ...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2008 Ford Edge AUTOMOBILES
Radiator, Replace
Vehicle: 2008 Ford Edge Limited 3.5 V6 GAS
- Drain cooling system into a suitable container.
- Remove cooling fan motor and shroud.
- Remove front bumper cover.
- Disconnect upper radiator hose and lower degas bottle hose from radiator.
- Disconnect lower radiator ...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2008 Ford Edge AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2008 Ford Edge Limited 3.5 V6 GAS
- Raise and support vehicle.
- Working from top of vehicle, using a suitable belt tensioner release tool, rotate accessory drive belt tensioner clockwise and remove accessory drive belt...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2008 Ford Edge AUTOMOBILES
Component location diagrams for most 2008 Ford Edge cars and light trucks sold in the U.S. from 1990+.
 Liftgate Components Diagram for 2008 Ford Edge SE 3.5 V6 GASComponents on diagram: |
 Door Components Diagram for 2008 Ford Edge SEL 3.5 V6 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2008 Ford Edge AUTOMOBILES
OEM drawn wiring diagrams for most 2008 Ford Edge cars and light trucks sold in the U.S.
 2008 Ford Edge SE 3.5 V6 GAS Wiring DiagramComponents on diagram: |
 2008 Ford Edge SEL 3.5 V6 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2008 Ford Edge AUTOMOBILES
OEM TSB listings for most 2008 Ford Edge cars and light trucks sold in the U.S. from 1985+.
|
Document: POPPING/SNAPPING NOISE - FRONT OR REAR 18 INCH WHEELS - TURNING AT SLOW SPEED BELOW 10 MPH (16 KM/H) Vehicle: 2008 Ford Edge SEL 3.5 V6 GAS Symptoms: |
|
Document: SERVICE TIP - POWER TAKE-OFF UNIT (PTU) - RIGHT HAND INTERMEDIATE SHAFT SEAL LEAKS Vehicle: 2008 Ford Edge SEL 3.5 V6 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2008 Ford Edge AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2008 Ford Edge cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2008 Ford Edge cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2008 Ford Edge cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2008 Ford Edge cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Edge SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Ford Edge vehicle.
|
| Access the Complete guide! |
