Auto Parts Search
We have info for following modifications of 2008 Ford Crown Victoria
- 2008 Ford Crown Victoria 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:W
- 2008 Ford Crown Victoria 4.6 V8 FLEX, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:V
- 2008 Ford Crown Victoria Police Interceptor 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:W
- 2008 Ford Crown Victoria Police Interceptor 4.6 V8 FLEX, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:V
- 2008 Ford Crown Victoria LX 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:W
- 2008 Ford Crown Victoria LX 4.6 V8 FLEX, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:V
BRAKE SERVICE PROCEDURES FOR 2008 Ford Crown Victoria AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Ford Crown Victoria cars and light trucks from 1990+.
Disc Brakes -> Rear Disc & Parking Brakes -> Troubleshooting
Vehicle: 2008 Ford Crown Victoria LX 4.6 V8 FLEX
If roughness or vibration is encountered during highway operation or if pedal pumping is experienced at low speeds, the disc may have excessive thickness variation. Measure the disc at 12 points with a micrometer at a radius approximately one inch from the edge of the disc. If thickness measurements vary by more than .0005 inch, r...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Crown Victoria BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Ford Crown Victoria AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Ford Crown Victoria cars and light trucks from 1990+.
Disc Brakes -> Rear Disc & Parking Brakes -> Adjustments -> Crown Victoria, Grand Marquis & Town Car -> Fusion, Milan & MKZ -> MKS, Sable, Taurus & Taurus X -> Mustang -> Parking Brake
Vehicle: 2008 Ford Crown Victoria LX 4.6 V8 FLEX
Parking Brake
Crown Victoria, Grand Marquis & Town Car
- Apply parking brake control fully with 100 lbs., foot pedal effort, then release brake control.
- Place transmission in Neutral position, then raise and support vehicle.
- With parking brake control in Off position, grasp pensioner around housing.
- Unlock clip by pulling downward with suitable hook tool place into rounded end of clip and support pensioner.
- Tensioner spring will take up cable slack and load cables, while holding pensioner, lock clip by pushing up on bottom of clip. If clip does not slide up move assembly slightly to align c...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Crown Victoria BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Ford Crown Victoria AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Ford Crown Victoria cars and light trucks from 1990+.
Anti-Lock Brakes -> Crown Victoria, Grand Marquis & Town Car -> Diagnosis & Testing -> 2008 -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Crown Victoria & Grand Marquis -> Diagnostic Trouble Code Interpretation -> Pinpoint Tests -> Town Car
Vehicle: 2008 Ford Crown Victoria LX 4.6 V8 GAS
Accessing Diagnostic Trouble Codes
The anti-lock brake/traction assist electronic control module is capable of performing a self-test using a suitably programmed scan tool.
The anti-lock control module monitors system operation and stores all defined diagnostic trouble codes in its memory. It is important to understand the control module cannot recognize some failures. Therefore, if a problem exists and no diagnostic trouble codes are stored by the control module, other diagnostic steps must be followed. The module cannot store a diagnostic trouble code if there is no power to...
[[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Ford Crown Victoria BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Ford Crown Victoria AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Ford Crown Victoria cars and light trucks from 1990+.
Hydraulic Brake Systems -> Hydraulic Brake System Flush
Vehicle: 2008 Ford Crown Victoria Police Interceptor 4.6 V8 FLEX
Whenever new brake components are installed in the hydraulic system, it is recommended that the entire hydraulic system be thoroughly flushed with clean brake fluid.
It may sometime become required to flush out the system due to the presence of mineral oil, kerosene, gasoline, etc., which will cause swelling of rubber piston cups and valves and render them inoperative.
Flushing is performed at e...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Crown Victoria BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Ford Crown Victoria AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Ford Crown Victoria cars and light trucks from 1990+.
Disc Brakes -> Front Disc Brakes -> Precautions -> System Depressurizing
Vehicle: 2008 Ford Crown Victoria LX 4.6 V8 GAS
System Depressurizing
On models equipped with anti-lock brakes, hydraulic system must be depressurized prior to ...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Crown Victoria BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Ford Crown Victoria AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Ford Crown Victoria cars and light trucks from 1990+.
Disc Brakes -> Front Disc Brakes -> Brake System Bleed -> System Priming -> Wheel Bleeding Sequence
Vehicle: 2008 Ford Crown Victoria 4.6 V8 GAS
Pressure bleeding is recommended for all hydraulic disc brake systems.
Do not reuse brake fluid drained from the hydraulic system when bleeding the brakes. Ensure disc brake pistons are returned to their normal positions and the shoe and lining assemblies are properly seated.
Do not shake the pressure bleeder tank while air is being added or after it has been pressurized. This will prevent air from the tank getting into the lines. Do not move the tank during the bleeding operation. The tank should be kept at least one third full.
On models equipped with power brakes, exhaust the...
CLICK HERE TO GET FULL ACCESS TO 2008 Ford Crown Victoria BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Ford Crown Victoria vehicle. |
Access the Complete guide! |