Auto Parts Search
We have info for following modifications of 2008 Dodge Durango
- 2008 Dodge Durango Adventurer 4.7 V8 GAS, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
- 2008 Dodge Durango Adventurer 5.7 V8 GAS, CID:345, Fuel Injection, Aspiration:345, Engine VIN:, Desg:2
- 2008 Dodge Durango Adventurer 4.7 V8 FLEX, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:P
- 2008 Dodge Durango Limited 4.7 V8 GAS, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
- 2008 Dodge Durango Limited 5.7 V8 GAS, CID:345, Fuel Injection, Aspiration:345, Engine VIN:, Desg:2
- 2008 Dodge Durango Limited 4.7 V8 FLEX, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:P
- 2008 Dodge Durango SXT 4.7 V8 GAS, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
- 2008 Dodge Durango SXT 3.7 V6 GAS, CID:226, Fuel Injection, Aspiration:226, Engine VIN:, Desg:K
- 2008 Dodge Durango SXT 4.7 V8 FLEX, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:P
- 2008 Dodge Durango SLT 3.7 V6 GAS, CID:226, Fuel Injection, Aspiration:226, Engine VIN:, Desg:K
- 2008 Dodge Durango SLT 5.7 V8 GAS, CID:345, Fuel Injection, Aspiration:345, Engine VIN:, Desg:2
- 2008 Dodge Durango SLT 4.7 V8 FLEX, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:P
- 2008 Dodge Durango SLT 4.7 V8 GAS, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Durango AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Durango cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 Dodge Durango SLT 5.7 V8 GAS
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate, if equipped.
- Remove hub nut from the half shaft.
- Remove brake caliper and rotor.
- Remove wheel speed sensor if equipped.
- Remove hub bearing bolts from the knuckle.
- Remove hub bearing and brake shield from knuckle.
- Support half shaft at the C/V joint housings.
- Position two pry bars behind the inn...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Durango DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Durango AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Durango cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2008 Dodge Durango Limited 4.7 V8 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate, if equipped.
- Mark a reference line across propeller shaft flange and pinion flange.
- Remove exhaust crossover bolts from exhaust manifolds and lower crossover.
- Remove boot clamp from CV joint.
- Remove pinion flange bolts.
- Slide propeller shaft off transfer case and remove shaft.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Replace old pinion flange bolts with new bolts and coat with Loctite 242 threadlocker.
- Torque pinion flange bolts to 65 ft. lbs.
Rear
- With vehicle in neutral, posit...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Durango DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Durango AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Durango cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2008 Dodge Durango Adventurer 5.7 V8 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate, if equipped.
- Mark a reference line across propeller shaft flange and pinion flange.
- Remove exhaust crossover bolts from exhaust manifolds and lower crossover.
- Remove boot clamp from CV joint.
- Remove pinion flange bolts.
- Slide propeller shaft off transfer case and remove shaft.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Replace old pinion flange bolts with new bolts and coat with Loctite 242 threadlocker.
- Torque pinion flange bolts to 65 ft. lbs.
Rear
- With vehicle in neutral, posit...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Durango DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Durango AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Durango cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 Dodge Durango SLT 4.7 V8 GAS
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate, if equipped.
- Remove hub nut from the half shaft.
- Remove brake caliper and rotor.
- Remove wheel speed sensor if equipped.
- Remove hub bearing bolts from the knuckle.
- Remove hub bearing and brake shield from knuckle.
- Support half shaft at the C/V joint housings.
- Position two pry bars behind the inn...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Durango DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Durango AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Durango cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2008 Dodge Durango SXT 4.7 V8 GAS
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate, if equipped.
- Mark a reference line across propeller shaft flange and pinion flange.
- Remove exhaust crossover bolts from exhaust manifolds and lower crossover.
- Remove boot clamp from CV joint.
- Remove pinion flange bolts.
- Slide propeller shaft off transfer case and remove shaft.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Replace old pinion flange bolts with new bolts and coat with Loctite 242 threadlocker.
- Torque pinion flange bolts to 65 ft. lbs.
Rear
- With vehicle in neutral, posit...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Durango DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Durango AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Durango cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2008 Dodge Durango SXT 4.7 V8 FLEX
Front
- With vehicle in neutral, position vehicle on hoist.
- Remove skid plate, if equipped.
- Mark a reference line across propeller shaft flange and pinion flange.
- Remove exhaust crossover bolts from exhaust manifolds and lower crossover.
- Remove boot clamp from CV joint.
- Remove pinion flange bolts.
- Slide propeller shaft off transfer case and remove shaft.
- Reverse procedure to install, noting the following:
- Align reference marks.
- Replace old pinion flange bolts with new bolts and coat with Loctite 242 threadlocker.
- Torque pinion flange bolts to 65 ft. lbs.
Rear
- With vehicle in neutral, posit...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Durango DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Dodge Durango vehicle. |
Access the Complete guide! |