Auto Parts Search
2007 Mercury Milan CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Mercury REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
BRAKE SERVICE PROCEDURES FOR 2007 Mercury Milan AUTOMOBILES
Disc Brakes -> Rear Disc & Parking Brakes -> Inspection
Vehicle: 2007 Mercury Milan 3.0 V6 GAS
Remove wheels and inspect brake disc, calipers and linings.
If the caliper is cracked or fluid leakage through the casting is evident, it must be replaced as a unit.
If caliper was removed when installing new components, clean all components in alcohol, then wipe dry using lint-free cloths. Using an air hose, blow out drilled passages and bores. Inspect dust boots for punctures or tears. If punctures or tears are evident, install new boots during assembly.
Inspect piston bores in both housings for scoring or pitting. Bores showing light scratches or corrosion can usually be cleaned with...
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Mercury Milan AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2007 Mercury Milan Premier 2.3 L4 GAS
- Remove front tire and wheel.
- Apply brake to keep halfshaft from rotating.
- Remove and discard front wheel hub nut.
- Remove front and rear lower control arm nuts.
- Using a suitable tool, disconnect 2 ball joints. Once pressure is applied to ball joint with a suitable tool, it may be necessary to tap wheel knuckle at ball joint area to separate ball joint from wheel knuckle.
- Using a suitable tool, separate halfshaft from wheel hub. When lower ball joint is separated from wheel knuckle, lower arm may strike outer constant velocity (CV) joint boot with enough force to damage boot cla...
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2007 Mercury Milan AUTOMOBILES
Alternator, Replace
Vehicle: 2007 Mercury Milan Premier 2.3 L4 GAS
- Disconnect battery ground cable.
- Remove bolt, nuts, and alternator upper air duct.
- Rotate accessory drive belt tensioner clockwise, then position accessory drive belt aside.
- Remove nuts and alternator shield.
- Press locking tabs and remove alternator intermediate air duct.
- Position alternator protective cover aside, remove nuts and position alt...
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2007 Mercury Milan AUTOMOBILES
Ford Motor Co. Cars -> Anti-Lock Brake Warning Lamp ->
Vehicle: 2007 Mercury Milan Premier 3.0 V6 GAS
This lamp should light when the ignition is turned On. It may light for as long as 30 seconds as a bulb and system inspect. If the lamp remains lit or lights while operating the vehicle, a fault condition in the anti-lock brake system is indicated. When the lamp is lit, turn ignition Off, then start...
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2007 Mercury Milan AUTOMOBILES
Heater Hose, Replace -> Bypass -> Inlet -> Outlet
Vehicle: 2007 Mercury Milan 3.0 V6 GAS
Inlet
- Drain cooling system into a suitable container.
- Reposition heater hose inlet clamp at heater core.
- Remove heater inlet hose from heater core.
- Reposition heater core inlet hose clamp at thermostat outlet.
- Remove hose from thermostat outlet.
- Remove hose from vehicle.
- Reverse procedure to install.
Outlet
- Drain cooling system into a suitable container.
- Reposition heater hose outl...
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2007 Mercury Milan AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2007 Mercury Milan 2.3 L4 GAS
- Disconnect battery ground cable from battery.
- Place vehicle in neutral and position on lift.
- Remove bolts and position righthand fender splash shield aside.
- Remove six pin-type retainers from righ...
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2007 Mercury Milan AUTOMOBILES
Component location diagrams for most 2007 Mercury Milan cars and light trucks sold in the U.S. from 1990+.
Brake Shift Interlock Solenoid Diagram for 2007 Mercury Milan Premier 2.3 L4 GAS Components on diagram: |
Rear Body Harness Diagram for 2007 Mercury Milan Premier 2.3 L4 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2007 Mercury Milan AUTOMOBILES
OEM drawn wiring diagrams for most 2007 Mercury Milan cars and light trucks sold in the U.S.
2007 Mercury Milan 3.0 V6 GAS Wiring Diagram Components on diagram: |
2007 Mercury Milan 2.3 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2007 Mercury Milan AUTOMOBILES
OEM TSB listings for most 2007 Mercury Milan cars and light trucks sold in the U.S. from 1985+.
Document: TRANSMISSION HARD SHIFTING - NO DTCS - MILEAGE ABOVE 20,000 MILES - REVISED Vehicle: 2007 Mercury Milan Premier 2.3 L4 GAS Symptoms: |
Document: FRONT STRUT NOISE Vehicle: 2007 Mercury Milan Premier 2.3 L4 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2007 Mercury Milan AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2007 Mercury Milan cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2007 Mercury Milan cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2007 Mercury Milan cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2007 Mercury Milan cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2007 Mercury Milan SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2007 Mercury Milan vehicle. |
Access the Complete guide! |