Auto Parts Search
We have info for following modifications of 2007 Ford Explorer
- 2007 Ford Explorer XLT 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
- 2007 Ford Explorer XLT 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:8
- 2007 Ford Explorer Limited 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
- 2007 Ford Explorer Limited 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:8
- 2007 Ford Explorer Eddie Bauer 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
- 2007 Ford Explorer Eddie Bauer 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:8
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Explorer AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Explorer cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2007 Ford Explorer Eddie Bauer 4.0 V6 GAS
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Tighten transfer case flange bolts in a cross pattern.
- Torque flange bolts to 22 ft. lbs.
- Torque U-joint retainer bolts to 26 ft. lbs.
Rear
One P...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Explorer DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Explorer AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Explorer cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2007 Ford Explorer XLT 4.0 V6 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Explorer DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Explorer AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Explorer cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2007 Ford Explorer Eddie Bauer 4.6 V8 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Explorer DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Explorer AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Explorer cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Ford Explorer XLT 4.0 V6 GAS
Front
- Loosen front axle wheel hub retainer.
- With vehicle in NEUTRAL, position on a hoist.
- Remove front wheel and tire assembly.
- Remove rear disc brake caliper and suspend aside using mechanics wire.
- Remove front axle wheel hub retaining nut.
- Remove tie rod end nut and separate tie rod end from knuckle.
- Remove stabilizer bar link nut.
- Remove upper ball joint nut and separate upper ball joint from knuckle.
- Remove CV shaft assembly from vehicle.
- Reverse procedure to install, noting the following:
- Torque axle shaft hub nut to 184 ft. lbs.
- Torque upper ball joint nut to 51 ft. lbs.
- Torque ...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Explorer DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Explorer AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Explorer cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2007 Ford Explorer XLT 4.6 V8 GAS
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Tighten transfer case flange bolts in a cross pattern.
- Torque flange bolts to 22 ft. lbs.
- Torque U-joint retainer bolts to 26 ft. lbs.
Rear
One P...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Explorer DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Explorer AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Ford Explorer cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Ford Explorer XLT 4.6 V8 GAS
Front
- Loosen the front axle wheel hub retainer.
- With the vehicle in NEUTRAL, position on a hoist.
- Remove the front wheel and tire assembly.
- Remove rear disc brake caliper and suspend aside using mechanics wire.
- Remove front axle wheel hub retaining nut.
- Remove tie rod end nut and separate tie rod end from knuckle.
- Remove stabilizer bar link nut.
- Remove upper ball joint nut and separate upper ball joint from knuckle.
- Remove CV shaft assembly from vehicle.
- Reverse procedure to install, noting the following:
- Torque axle shaft hub nut to 184 ft. lbs.
- Torque upper ball joint nut to 51 ft....
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Explorer DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2007 Ford Explorer vehicle. |
Access the Complete guide! |