Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2006 Ford Freestyle car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2006 Ford Freestyle automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2006 Ford Freestyle
- 2006 Ford Freestyle Limited 3.0 V6 GAS, CID:183, Fuel Injection, Aspiration:183, Engine VIN:, Desg:1
- 2006 Ford Freestyle SE 3.0 V6 GAS, CID:183, Fuel Injection, Aspiration:183, Engine VIN:, Desg:1
- 2006 Ford Freestyle SEL 3.0 V6 GAS, CID:183, Fuel Injection, Aspiration:183, Engine VIN:, Desg:1
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Ford Freestyle AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Ford Freestyle cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2006 Ford Freestyle SE 3.0 V6 GAS
Front
- Remove center hub cap from wheel.
- Loosen hub nut.
- Raise and support vehicle.
- Remove front wheel and tire assembly.
- Remove hub nut and washer.
- Remove front brake anti-lock sensor harness from clip.
- Remove and position front brake anti-lock sensor aside.
- Remove and discard lower ball joint nut.
- Remove lower strut support nut and bolt. Discard nut.
- Using suitable tools, press ball joint stud until it is loose in knuckle.
- Wire knuckle to strut. This will prevent knuckle from falling off of strut while knuckle and lower ball joint are separated. Failure to follow these instructions...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Freestyle DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Ford Freestyle AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Ford Freestyle cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Rear
Vehicle: 2006 Ford Freestyle Limited 3.0 V6 GAS
Rear
- Raise and support vehicle.
- Remove muffler and tall pipe assembly.
- Remove exhaust support brace bolts, then the exhaust support brace.
- Remove and discard driveshaft flange bolts from rear axle pinion flange, then disconnect driveshaft from rear axle pinion flange. Failure to correctly index-mark the driveshaft will lead to noise, vibration or harshness (NVH) problems. Index-mark the driveshaft to the rear axle pinion flange, the power take off (PTO) flange and the center bearing bracket. Index-mark the driveshaft.
- Remove and discard driveshaft flange bolts from PTO flang...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Freestyle DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Ford Freestyle AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Ford Freestyle cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2006 Ford Freestyle SEL 3.0 V6 GAS
Front
- Remove center hub cap from wheel.
- Loosen hub nut.
- Raise and support vehicle.
- Remove front wheel and tire assembly.
- Remove hub nut and washer.
- Remove front brake anti-lock sensor harness from clip.
- Remove and position front brake anti-lock sensor aside.
- Remove and discard lower ball joint nut.
- Remove lower strut support nut and bolt. Discard nut.
- Using suitable tools, press ball joint stud until it is loose in knuckle.
- Wire knuckle to strut. This will prevent knuckle from falling off of strut while knuckle and lower ball joint are separated. Failure to follow these instructions...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Freestyle DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Ford Freestyle AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Ford Freestyle cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Rear
Vehicle: 2006 Ford Freestyle SEL 3.0 V6 GAS
Rear
- Raise and support vehicle.
- Remove muffler and tall pipe assembly.
- Remove exhaust support brace bolts, then the exhaust support brace.
- Remove and discard driveshaft flange bolts from rear axle pinion flange, then disconnect driveshaft from rear axle pinion flange. Failure to correctly index-mark the driveshaft will lead to noise, vibration or harshness (NVH) problems. Index-mark the driveshaft to the rear axle pinion flange, the power take off (PTO) flange and the center bearing bracket. Index-mark the driveshaft.
- Remove and discard driveshaft flange bolts from PTO flang...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Freestyle DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Ford Freestyle AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Ford Freestyle cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2006 Ford Freestyle Limited 3.0 V6 GAS
Front
- Remove center hub cap from wheel.
- Loosen hub nut.
- Raise and support vehicle.
- Remove front wheel and tire assembly.
- Remove hub nut and washer.
- Remove front brake anti-lock sensor harness from clip.
- Remove and position front brake anti-lock sensor aside.
- Remove and discard lower ball joint nut.
- Remove lower strut support nut and bolt. Discard nut.
- Using suitable tools, press ball joint stud until it is loose in knuckle.
- Wire knuckle to strut. This will prevent knuckle from falling off of strut while knuckle and lower ball joint are separated. Failure to follow these instructions...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Freestyle DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Ford Freestyle AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Ford Freestyle cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Rear
Vehicle: 2006 Ford Freestyle SE 3.0 V6 GAS
Rear
- Raise and support vehicle.
- Remove muffler and tall pipe assembly.
- Remove exhaust support brace bolts, then the exhaust support brace.
- Remove and discard driveshaft flange bolts from rear axle pinion flange, then disconnect driveshaft from rear axle pinion flange. Failure to correctly index-mark the driveshaft will lead to noise, vibration or harshness (NVH) problems. Index-mark the driveshaft to the rear axle pinion flange, the power take off (PTO) flange and the center bearing bracket. Index-mark the driveshaft.
- Remove and discard driveshaft flange bolts from PTO flang...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Freestyle DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2006 Ford Freestyle vehicle.
|
| Access the Complete guide! |
