Auto Parts Search
We have info for following modifications of 2005 Ford F-450 Super Duty
- 2005 Ford F-450 Super Duty Lariat 6.0 V8 DIESEL, CID:363, Fuel Injection, Aspiration:363, Engine VIN:, Desg:P
- 2005 Ford F-450 Super Duty XL 6.0 V8 DIESEL, CID:363, Fuel Injection, Aspiration:363, Engine VIN:, Desg:P
- 2005 Ford F-450 Super Duty XLT 6.0 V8 DIESEL, CID:363, Fuel Injection, Aspiration:363, Engine VIN:, Desg:P
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Ford F-450 Super Duty AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Ford F-450 Super Duty cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2005 Ford F-450 Super Duty Lariat 6.0 V8 DIESEL
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2005 Ford F-450 Super Duty DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Ford F-450 Super Duty AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Ford F-450 Super Duty cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2005 Ford F-450 Super Duty XL 6.0 V8 DIESEL
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2005 Ford F-450 Super Duty DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Ford F-450 Super Duty AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Ford F-450 Super Duty cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2005 Ford F-450 Super Duty XLT 6.0 V8 DIESEL
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard four flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft flange bolts to 82 ft. lbs., if equipped.
- Torque front propeller shaft U-joint retainer bolts to 26 ft. lbs.
...
CLICK HERE TO GET FULL ACCESS TO 2005 Ford F-450 Super Duty DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Ford F-450 Super Duty AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Ford F-450 Super Duty cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2005 Ford F-450 Super Duty XL 6.0 V8 DIESEL
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard four flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft flange bolts to 82 ft. lbs., if equipped.
- Torque front propeller shaft U-joint retainer bolts to 26 ft. lbs.
...
CLICK HERE TO GET FULL ACCESS TO 2005 Ford F-450 Super Duty DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Ford F-450 Super Duty AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Ford F-450 Super Duty cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Double Cardan -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2005 Ford F-450 Super Duty XLT 6.0 V8 DIESEL
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2005 Ford F-450 Super Duty DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Ford F-450 Super Duty AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Ford F-450 Super Duty cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> One Piece Driveshaft -> Rear -> Three Piece Driveshaft -> Two Piece Driveshaft
Vehicle: 2005 Ford F-450 Super Duty Lariat 6.0 V8 DIESEL
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard four flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Torque front propeller shaft flange bolts to 82 ft. lbs., if equipped.
- Torque front propeller shaft U-joint retainer bolts to 26 ft. lbs.
...
CLICK HERE TO GET FULL ACCESS TO 2005 Ford F-450 Super Duty DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2005 Ford F-450 Super Duty vehicle. |
Access the Complete guide! |