Auto Parts Search
We have info for following modifications of 2003 Ford Taurus
- 2003 Ford Taurus 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:U
- 2003 Ford Taurus 3.0 V6 FLEX, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:2
- 2003 Ford Taurus 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:S
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Taurus AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Taurus cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Traction Control System Warning Lamp ->
Vehicle: 2003 Ford Taurus 3.0 V6 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned On as a bulb check. If the warni...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Taurus MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Taurus AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Taurus cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Electronic Compass -> 2002-03 Taurus -> Calibration Adjustment -> Zone Adjustment
Vehicle: 2003 Ford Taurus 3.0 V6 GAS
Zone Adjustment
- Determine compass magnetic zone, Fig. .
- Place ignition switch in On position.
- With compass display turned On, press and hold COMP side of control located on rear view mirror for no more than 6 seconds until the zone selection number appears. If a C appears, repeat step.
- Press COMP side of control to select proper zone setting, then release.
- To ...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Taurus MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Taurus AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Taurus cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Electronic Compass -> 2002-03 Taurus -> Calibration Adjustment -> Zone Adjustment
Vehicle: 2003 Ford Taurus 3.0 V6 FLEX
Zone Adjustment
- Determine compass magnetic zone, Fig. .
- Place ignition switch in On position.
- With compass display turned On, press and hold COMP side of control located on rear view mirror for no more than 6 seconds until the zone selection number appears. If a C appears, repeat step.
- Press COMP side of control to select proper zone setting, then release.
- To ...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Taurus MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Taurus AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Taurus cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Check Engine Lamp/Malfunction Indicator Lamp (MIL)/Service Engine Soon Lamp -> 1998-2006 Models -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool
Vehicle: 2003 Ford Taurus 3.0 V6 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-V system. If the lamp remains On or starts to blink, a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
A temporary fault such as running out of fuel, poor quality or water in fuel or loos...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Taurus MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Taurus AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Taurus cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Powertrain Malfunction Indicator ->
Vehicle: 2003 Ford Taurus 3.0 V6 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected in the powertrain system. If the lamp remains On a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Powertrain Malfunction Indicator will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Taurus MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2003 Ford Taurus AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2003 Ford Taurus cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Check Fuel Cap Lamp ->
Vehicle: 2003 Ford Taurus 3.0 V6 GAS
The Check Fuel Cap Lamp will illuminate momentarily when the ignition switch is placed in the On position as a bulb check. If the lamp remains...
CLICK HERE TO GET FULL ACCESS TO 2003 Ford Taurus MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2003 Ford Taurus vehicle. |
Access the Complete guide! |