Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2002 Saab 9-3 car and truck
repair procedures including Saab engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2002 Saab 9-3 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2002 Saab 9-3
- 2002 Saab 9-3 Viggen 2.3 L4 GAS, CC:2290, Fuel Injection
- 2002 Saab 9-3 SE 2.0 L4 GAS, CC:1985, Fuel Injection, Engine VIN:, Desg:K
BRAKE SERVICE PROCEDURES FOR 2002 Saab 9-3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Saab 9-3 cars and light trucks from 1990+.
Disc Brakes -> Tightening Specifications
Vehicle: 2002 Saab 9-3 SE 2.0 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 2002 Saab 9-3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Saab 9-3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Saab 9-3 cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Caliper Overhaul -> Caliper, Replace -> Front -> Rear
Vehicle: 2002 Saab 9-3 SE 2.0 L4 GAS
Caliper, Replace
Front
- Remove brake pads.
- Loosen brake hose at caliper.
- Press brake pedal fully to floor and secure in that position.
- Remove upper guide pin bolt, then disconnect brake hose at caliper and plug hose and fitting.
- Remove caliper.
- Reverse procedure to install and bleed brake system.
Rear
- Raise and support vehicle, then remove wheel.
- Press out brake pistons with suitable pliers.
- Depress brake pedal with brake clamp.
- Disconnect brake pipe from brake caliper, then plug pipes and brake caliper.
- Remove pins and locking spring, then the brake pads.
- Remove two brake caliper securing bol...
CLICK HERE TO GET FULL ACCESS TO 2002 Saab 9-3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Saab 9-3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Saab 9-3 cars and light trucks from 1990+.
Disc Brakes -> Tightening Specifications
Vehicle: 2002 Saab 9-3 Viggen 2.3 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 2002 Saab 9-3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Saab 9-3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Saab 9-3 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description
Vehicle: 2002 Saab 9-3 Viggen 2.3 L4 GAS
When the brake pedal is depressed, pedal pressure assisted by power from the servo unit pushes the input rod into the master cylinder. The input rod pushes the primary plunger up the bore which closes the cutoff port to the fluid reservoir. This creates pressure ahead of the primary plunger. This pressure also acts on the secondary plunger, pushing it up the bore and closing the cutoff port from the secondary chamber. The pressure in both circuits increases and, because the plungers are the same size, pressure in each circuit is the same. Fluid pressure is directed to the brake syst...
CLICK HERE TO GET FULL ACCESS TO 2002 Saab 9-3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Saab 9-3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Saab 9-3 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Disassemble -> Master Cylinder Overhaul
Vehicle: 2002 Saab 9-3 SE 2.0 L4 GAS
Master Cylinder Overhaul
When working on any hydraulic brake components it is extremely important to keep the work area clean. Clean any components that are to be reused with new brake fluid or a cleaning fluid specifically designed for hydraulic components. Wipe all components dry using clean lint-free paper or cloth. Gaskets, seals, O-rings and rubber components should not be reused. Prior to assembly, all components should be generously lubricated with clean brake fluid.
Disassemble
- Clamp master cylinder in soft-jaw vice.
- Remove rubber seals from brake hose connections.
- Carefull...
CLICK HERE TO GET FULL ACCESS TO 2002 Saab 9-3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Saab 9-3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Saab 9-3 cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 2002 Saab 9-3 Viggen 2.3 L4 GAS
The servo (booster) unit, Fig. , provides power assistance to the pedal effort applied. The servo obtains its power from vacuum created in the engine inlet manifold and provides assistance in a ratio of about 4 to 1. Should a vacuum failure occur, the two pushrods will act as a single rod, allowing brakes to work conventionally but with a much greater pedal effort.
When the brake pedal is depressed, then input rod pushes the...
CLICK HERE TO GET FULL ACCESS TO 2002 Saab 9-3 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2002 Saab 9-3 vehicle.
|
| Access the Complete guide! |
