Auto Parts Search
2002 Chrysler Sebring CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Chrysler REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 2002 Chrysler Sebring AUTOMOBILES
Air Bag System Precautions -> DaimlerChrysler -> Disarming -> 1990-97 -> 1994-96 Cherokee -> 1998-2004 -> Except 1994-96 Cherokee -> Light Trucks & Vans -> Passenger Cars
Vehicle: 2002 Chrysler Sebring 2.7 V6 GAS
Passenger Cars
1990-97
It may be required to access and record all Diagnostic Trouble Codes (DTCs) prior to disarming the air bag system.
- Place ignition switch in Lock position.
- Disconnect and isolate battery ground cable.
- Wait at least two minutes after disconnecting battery ground cable before doing any further work on vehicle. The air bag system is designed to retain enough voltage to deploy air bags for a short time even after battery has been disconnected.
1998-2004
It may be required to access and rec...
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Chrysler Sebring AUTOMOBILES
Hydraulic Brake Systems -> Brake System Bleed -> Bench Bleeding -> Manual Bleed -> Master Cylinder Bleed -> On-Vehicle Bleeding -> Pressure Bleed
Vehicle: 2002 Chrysler Sebring 2.7 V6 GAS
Pressure Bleed
Use bleeder tank tool No. C-3496-B, or equivalent, and adapter tool No. BB400-9A, or equivalent, to pressurize hydraulic system.
Normal pressure bleeder pressure should not be more than 35 psi. On models equipped with plastic reservoirs, do not exceed 25 psi bleeding pressure.
- Attach suitable clear plastic hose to bleeder screw and submerge other end into clear container with clean brake fluid.
- Open bleeder screw at least one full turn.
- Bleed 4-8 ounces of fluid through system until air free flow is maintained.
- Repeat procedure at all screws.
- If pedal travel is excess...
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2002 Chrysler Sebring AUTOMOBILES
DaimlerChrysler/AMC/Eagle Passenger Cars -> Fuel Filter Replacement -> Breeze, Cirrus, Sebring Convertible, Sebring Sedan & Stratus Sedan w/2.5L, 2000-05 2.0L, 2.4L & 2.7L Engines -> Fuel System Pressure Relief -> Removal & Installation
Vehicle: 2002 Chrysler Sebring 2.7 V6 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
After the battery has been disconnected and reconnected, some abnormal driveability symptoms may occur. The vehicle may need to be driven while it relearns its adaptive strategy.
Fuel Sys...
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2002 Chrysler Sebring AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2002 Chrysler Sebring 2.4 L4 GAS
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove driveshaft nut, Fig. .
- Disconnect tie rod end and stabilizer link.
- Remove damper fork.
- Disconnect lateral lower arm and compression lower arm.
- Remove harness clip.
- Remove driveshaft to transaxle bolt.
- Tap center bearing bracket lightly with plastic hammer to remove ...
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2002 Chrysler Sebring AUTOMOBILES
Alternator, Replace
Vehicle: 2002 Chrysler Sebring 2.4 L4 GAS
- Disconnect battery ground cable.
- Remove drive belt cover.
- Unplug field circuit from alternator.
- Remove B+ terminal cover by spreading cover using a suitable small flat blade tool.
- Remove B+ terminal nu...
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2002 Chrysler Sebring AUTOMOBILES
Chrysler LLC Cars -> Air Bag Warning Lamp ->
Vehicle: 2002 Chrysler Sebring 2.4 L4 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned On as a bulb check. If the Air B...
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2002 Chrysler Sebring AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2002 Chrysler Sebring 2.4 L4 GAS
Lower
- Disconnect negative battery cable.
- Drain cooling system into a suitable container.
- Reposition hose clamp from water inlet pipe.
- Remove radiator outlet hose from water inlet pipe.
- Reposition hose clamp from radiator.
- Remove radiator outlet hose from radiator and vehicle.
- Reverse procedure t...
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2002 Chrysler Sebring AUTOMOBILES
Serpentine Drive Belt, Replace -> Air Conditioning Compressor & Alternator Belt -> Installation -> Removal
Vehicle: 2002 Chrysler Sebring 2.7 V6 GAS
Air Conditioning Compressor & Alternator Belt
Removal
- Raise and support vehicle.
- Remove righthand front tire and wheel assembly.
- Remove drive belt splash shield.
- Insert suitable 3/8 inch drive breaker bar into square opening of belt tensioner pivot plate.
- Rotate belt tensioner clockwise until tensioner bottoms out, then r...
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2002 Chrysler Sebring AUTOMOBILES
Component location diagrams for most 2002 Chrysler Sebring cars and light trucks sold in the U.S. from 1990+.
Transmission Control Module Diagram for 2002 Chrysler Sebring 2.4 L4 GAS Components on diagram: |
Brake Switch Diagram for 2002 Chrysler Sebring 2.4 L4 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2002 Chrysler Sebring AUTOMOBILES
OEM drawn wiring diagrams for most 2002 Chrysler Sebring cars and light trucks sold in the U.S.
2002 Chrysler Sebring 3.0 V6 GAS Wiring Diagram Components on diagram: |
2002 Chrysler Sebring 2.4 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2002 Chrysler Sebring AUTOMOBILES
OEM TSB listings for most 2002 Chrysler Sebring cars and light trucks sold in the U.S. from 1985+.
Document: AUTOMATIC TRANSMISSION DIAGNOSTIC TEARDOWN PROCEDURE - REVISED Vehicle: 2002 Chrysler Sebring 2.4 L4 GAS Auto Systems: |
Document: AUTOMATIC TRANSMISSION DIAGNOSTIC TEARDOWN PROCEDURE - REVISED Vehicle: 2002 Chrysler Sebring 2.4 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2002 Chrysler Sebring AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2002 Chrysler Sebring cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2002 Chrysler Sebring cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2002 Chrysler Sebring cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2002 Chrysler Sebring cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2002 Chrysler Sebring SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2002 Chrysler Sebring vehicle. |
Access the Complete guide! |