Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Pontiac Montana car and truck
repair procedures including Pontiac engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Pontiac Montana automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Montana cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Caliper Service -> Assemble -> Blazer, Bravada & Jimmy -> Disassemble -> Front -> Inspection -> Installation -> Rear -> Removal -> Sierra & Silverado
Vehicle: 2000 Pontiac Montana 3.4 V6 GAS
Removal
Front
- Siphon brake fluid out of master cylinder until fluid level is approximately 1/3 full, this will prevent fluid overflow when caliper piston is pushed back into its bore.
- Raise and support vehicle, then remove wheels.
- Push piston back into its bore using suitable C-clamp, Fig. .
- Remove two caliper mounting bolts and lift caliper off of rotor.
Rear
Blazer, Bravada & Jimmy
- Raise and support vehicle.
- Mark position of wheel to hub for installation reference.
- Remove wheel assembly.
- Remove mounting bolt and disconnect brake hose fitting from caliper. Discard gaskets and plug brake h...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Montana cars and light trucks from 1990+.
Drum Brakes -> Tightening Specifications;
Vehicle: 2000 Pontiac Montana 3.4 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Montana cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Rotor Replacement -> 2WD Models -> 4WD Models -> Astro, Blazer, Bravada, Jimmy, K1500/2500 & T Series Pickup -> Except Montana, Silhouette, Trans Sport & Venture -> Front -> K3500 -> Montana, Silhouette, Trans Sport & Venture -> Rear
Vehicle: 2000 Pontiac Montana 3.4 V6 GAS
2WD Models
Except Montana, Silhouette, Trans Sport & Venture
Front
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove caliper as outlined under "Caliper Service."
- Remove grease cap from hub/rotor, Fig. .
- Remove cotter pin, nut and washer.
- Remove hub/rotor from spindle, being careful not to damage spindle threads or outer bearing.
- Reverse procedure to install, noting the following:
- Apply high-temperature wheel bearing grease to inner and outer wheel bearings.
- Torque nut to 12 ft. lbs. while turning wheel assembly forward by hand, back nut off one flat or until hole in spindle...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Montana cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> Power Brake Unit Service
Vehicle: 2000 Pontiac Montana 3.4 V6 GAS
The power brake unit is n...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Montana cars and light trucks from 1990+.
Drum Brakes -> Inspection -> Adjuster Mechanism -> Backing Plate -> Brake Drums -> Brake Linings & Springs -> General System -> Parking Brake Cable
Vehicle: 2000 Pontiac Montana 3.4 V6 GAS
General System
- Inspect components for damage or unusual wear. Replace as required.
- Inspect backing plate mounting bolts and ensure they are tight.
- Inspect wheel cylinders. Excessive fluid indicates cup leakage and need for wheel cylinder replacement. Slight amount of fluid is always present and is considered normal, acting as lubricant for cylinder pistons.
- Check adjuster screw operation. If satisfactory, lightly lubricate adjusting screw and washer with suitable brake lube. If operation is unsatisfactory, replace.
- C clean rust and dirt from shoe contact surfaces on backing plate using fi...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Montana BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Pontiac Montana AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Pontiac Montana cars and light trucks from 1990+.
Anti-lock Brakes -> Kelsey-Hayes -> Precautions -> Battery Ground Cable -> Delco LOC II -> General Service Precautions -> Radio Security System -> Theftlock
Vehicle: 2000 Pontiac Montana 3.4 V6 GAS
Battery Ground Cable
Prior to service disconnect battery ground cable and isolate as required.
Radio Security System
Theftlock
If the Theftlock system is active when battery power is interrupted, the customers security code must be entered to restore proper function of the radio. To unlock a secured radio after power loss, proceed as follows:
- "LOC" appears with ignition in On position.
- Press "NM" and "000" will appear on display.
- Press "NM" again to make last two digits agree with security code.
- Press "HR" to make first 1 or 2 digits agree with security code.
- Press "AM-FM" to select code entered. "SEC" wi...
CLICK HERE TO GET FULL ACCESS TO 2000 Pontiac Montana BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2000 Pontiac Montana vehicle.
|
| Access the Complete guide! |
