Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1999 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Toyota Sienna cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Brake Lines -> Master Cylinder
Vehicle: 1999 Toyota Sienna 3.0 V6 GAS
Master Cylinder
- Fill reservoir with fluid.
- Disconnect tubes from master cylinder. Then slowly depress brake pedal and hold.
- Block off outlet holes with fingers, and release pedal. Repeat three or four times.
Brake Lines
Bleed wheel with longest brake line first, then work your way...
CLICK HERE TO GET FULL ACCESS TO 1999 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Toyota Sienna cars and light trucks from 1990+.
Disc Brakes -> Front Disc Brakes -> Disc Brake Specifications
Vehicle: 1999 Toyota Sienna 3.0 V6 GAS
Refer to the disc brake specifications under "Rear ... "
CLICK HERE TO GET FULL ACCESS TO 1999 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Toyota Sienna cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Disassemble -> Except Sienna -> Inspection -> Master Cylinder -> Overhaul -> Sienna -> Wheel Cylinders
Vehicle: 1999 Toyota Sienna 3.0 V6 GAS
Master Cylinder
Except Sienna
Disassemble
For the following procedures, refer to Fig. for assistance.
- Remove master cylinder boot.
- Remove setscrew and reservoir tank, then the cap and strainer from reservoir.
- Remove two grommets and place cylinder in vise.
- Push piston in and remove stopper bolt, Fig. .
- Push pistons in and remove snap ring, then No. 1 piston carefully by hand.
- Place cylinder on edges of two wooden blocks and tap on cylinder until No. 2 piston comes out.
Inspection
Clean parts with compressed air. Inspect cylinder bore for rust and scoring. Also, inspect for wear or damag...
CLICK HERE TO GET FULL ACCESS TO 1999 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Toyota Sienna cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 1999 Toyota Sienna 3.0 V6 GAS
When the brake pedal is depressed, a vacuum builds up in the booster which amplifies the pedal force, pressing on the piston in the master cylinder. The piston raises the hydraulic pressure in the cylinder. This hydr...
CLICK HERE TO GET FULL ACCESS TO 1999 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Toyota Sienna cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> 2WD -> 4WD -> Camry & Camry Solara -> Celica & Corolla -> Echo & Tercel -> Inspection -> Installation -> Land Cruiser, Tundra & 4Runner -> RAV4 -> Removal -> Replacement -> Sienna -> Tacoma & T100
Vehicle: 1999 Toyota Sienna 3.0 V6 GAS
Camry & Camry Solara
Removal
- Raise and support rear of vehicle, then remove wheel and tire assembly.
- Remove brake drum. If brake drum cannot be remove easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
- Disconnect return spring, then remove front shoe hold-down spring, retainers and pin.
- Disconnect anchor spring, then remove front brake shoe and anchor spring, Fig. .
- Remove rear shoe hold-down spring, retainers and pin, using suitable tool, then disconnect parking brake cable from anchor plate.
- D...
CLICK HERE TO GET FULL ACCESS TO 1999 Toyota Sienna BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Toyota Sienna AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Toyota Sienna cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description
Vehicle: 1999 Toyota Sienna 3.0 V6 GAS
When the brake pedal is depressed, a vacuum builds up in the booster which amplifies the pedal force, pressing on the piston in the master cylinder. The piston raises the hydraulic pressure in the cylinder. This hydraulic ...
CLICK HERE TO GET FULL ACCESS TO 1999 Toyota Sienna BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1999 Toyota Sienna vehicle. |
Access the Complete guide! |