Auto Parts Search
We have info for following modifications of 1999 Chevrolet Tahoe
- 1999 Chevrolet Tahoe 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:R
- 1999 Chevrolet Tahoe 6.5 V8 DIESEL, CID:395, Fuel Injection, Aspiration:395, Engine VIN:, Desg:S
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Tahoe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Tahoe cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Astro, Bravada, S & T Series & Safari -> Aztek -> C & K Series -> Duo-Servo -> G Series -> Installation -> Montana, Silhouette, Trans Sport & Venture -> P Series -> Removal -> Single-Servo -> Tracker
Vehicle: 1999 Chevrolet Tahoe 5.7 V8 GAS
C & K Series
Duo-Servo
Removal
- Raise and support vehicle.
- Mark relationship of wheel to hub, then remove tire and wheel assembly.
- On models equipped with full-floating axles, remove hub and drum assembly as described in "Drive Axles."
- On models equipped with semi-floating axles, proceed as follows:
- Install pin into park brake lever.
- Mark relationship of drum to axle.
- Remove rear brake drum retainers, as required.
- Remove rear brake drum.
- On all models, remove return springs and shoe guide, Fig. .
- Remove brake hold down springs and pins.
- Disconnect actuator lever and pivot.
- Remove lever return spri...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Tahoe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Tahoe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Tahoe cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Caliper Service -> Assemble -> Blazer, Bravada & Jimmy -> Disassemble -> Front -> Inspection -> Installation -> Rear -> Removal -> Sierra & Silverado
Vehicle: 1999 Chevrolet Tahoe 6.5 V8 DIESEL
Removal
Front
- Siphon brake fluid out of master cylinder until fluid level is approximately 1/3 full, this will prevent fluid overflow when caliper piston is pushed back into its bore.
- Raise and support vehicle, then remove wheels.
- Push piston back into its bore using suitable C-clamp, Fig. .
- Remove two caliper mounting bolts and lift caliper off of rotor.
Rear
Blazer, Bravada & Jimmy
- Raise and support vehicle.
- Mark position of wheel to hub for installation reference.
- Remove wheel assembly.
- Remove mounting bolt and disconnect brake hose fitting from caliper. Discard gaskets and plug brake h...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Tahoe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Tahoe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Tahoe cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder
Vehicle: 1999 Chevrolet Tahoe 5.7 V8 GAS
Master Cylinder
- On models equipped with manual brake system, disconnect master cylinder pushrod from brake pedal.
- On all models, disconnect all wire conne...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Tahoe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Tahoe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Tahoe cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Precautions -> Brake Disc Service -> Brake Lines & Linings -> Brake Roughness -> General
Vehicle: 1999 Chevrolet Tahoe 5.7 V8 GAS
Brake Lines & Linings
Remove one of the front wheels and inspect the brake disc, caliper and linings.
Do not allow any oil or grease on the linings. It is recommended that linings be replaced in sets when worn or damaged.
If the caliper is cracked or fluid leakage through the casting is evident, it must be replaced as a unit.
Brake Roughness
The most common cause of brake chatter on disc brakes is a variation in thickness of the disc. If roughness or vibration is encountered during highway operation or if pedal pumping is experienced at low speeds, the disc may have excessive thickness v...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Tahoe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Tahoe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Tahoe cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> Troubleshooting -> Brakes Grab -> Hard Pedal -> Slow Or No Release
Vehicle: 1999 Chevrolet Tahoe 6.5 V8 DIESEL
Hard Pedal
- Internal vacuum leak.
- Faulty control valve.
- Broken or damaged hydraulic brake lines.
- Collapsed or damaged vacuum hose.
- Plugged or loose vacuum fitting.
- Bad stud welds on front or rear housing on power head.
- Faulty booster diaphragm.
- Restricted air filter element.
- Worn or distorted reaction plate or levers.
- Cracked or broken pow...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Tahoe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Tahoe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Tahoe cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Rotor Replacement -> 2WD Models -> 4WD Models -> Astro, Blazer, Bravada, Jimmy, K1500/2500 & T Series Pickup -> Except Montana, Silhouette, Trans Sport & Venture -> Front -> K3500 -> Montana, Silhouette, Trans Sport & Venture -> Rear
Vehicle: 1999 Chevrolet Tahoe 5.7 V8 GAS
2WD Models
Except Montana, Silhouette, Trans Sport & Venture
Front
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove caliper as outlined under "Caliper Service."
- Remove grease cap from hub/rotor, Fig. .
- Remove cotter pin, nut and washer.
- Remove hub/rotor from spindle, being careful not to damage spindle threads or outer bearing.
- Reverse procedure to install, noting the following:
- Apply high-temperature wheel bearing grease to inner and outer wheel bearings.
- Torque nut to 12 ft. lbs. while turning wheel assembly forward by hand, back nut off one flat or until hole in spindle...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Tahoe BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1999 Chevrolet Tahoe vehicle. |
Access the Complete guide! |