Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1997 Subaru Legacy car and truck
repair procedures including Subaru engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1997 Subaru Legacy automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1997 Subaru Legacy
- 1997 Subaru Legacy L 2.2 H4 GAS, CC:2212, Fuel Injection, Engine VIN:, Desg:4
- 1997 Subaru Legacy LSI 2.5 H4 GAS, CC:2458, Fuel Injection, Engine VIN:, Desg:6
- 1997 Subaru Legacy GT 2.5 H4 GAS, CC:2458, Fuel Injection, Engine VIN:, Desg:6
- 1997 Subaru Legacy Brighton 2.2 H4 GAS, CC:2212, Fuel Injection, Engine VIN:, Desg:4
- 1997 Subaru Legacy Outback 2.5 H4 GAS, CC:2458, Fuel Injection, Engine VIN:, Desg:6
- 1997 Subaru Legacy Postal 2.2 H4 GAS, CC:2212, Fuel Injection, Engine VIN:, Desg:4
- 1997 Subaru Legacy Limited 2.5 H4 GAS, CC:2458, Fuel Injection, Engine VIN:, Desg:6
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Legacy AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Legacy cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> Front -> Rear
Vehicle: 1997 Subaru Legacy Postal 2.2 H4 GAS
Front
- Raise and support vehicle.
- Remove front wheels.
- Disconnect brake hose from strut.
- Remove caliper lockpin, then rotate caliper on guide pin, Figs. through .
- Remove brake pads from support.
- Reverse procedure to install noting the following:
- Push piston into caliper body. When piston is difficult to insert, loosen the air bleeder, then push into place.
- Refer to Figs. and for tightening values.
- After completing installation, depress brake pedal several times to seat brake pads against rotor. If pedal stroke is excessive, bleed hydraulic system as outlined under, "Hydraulic Brake S... "
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Legacy BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Legacy AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Legacy cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description -> Dual Proportioning Valve (DPV) -> Master Cylinder
Vehicle: 1997 Subaru Legacy L 2.2 H4 GAS
Master Cylinder
The master cylinder is of the tandem type design and incorporates a fast fill valve in order to improve the feeling on braking. It has a dual design which consists of a primary and a secondary brake system. If one brake system becomes inoperative, the other line will provide braking action. The master cylinder is designed into a "pierce" form so that ...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Legacy BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Legacy AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Legacy cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Master Cylinder
Vehicle: 1997 Subaru Legacy LSI 2.5 H4 GAS
Master Cylinder
- Remove master cylinder from vehicle.
- Remove cylinder pin, Fig. .
- Push piston inward, then remove snap ring.
- Apply pressure to piston assembly while Inserting a small screwdriver into window of piston retainer and raise piston retainer latch, Fig. .
- Remove primary and secondary piston assemblies. Do not disassemble pistons. if disassembled, the spring settings will change.
- Inspect master cylinder inside diameter to piston clearance, Service limit is not to exceed 0.043 inch.
- Clean all parts with clean brake fluid, do...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Legacy BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Legacy AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Legacy cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 1997 Subaru Legacy Postal 2.2 H4 GAS
- Ensure there are no fluid leaks from joints or connections.
- When bleeding brakes, bleed brakes connected to the secondary chamber of the master cylinder, then bleed brakes connected to the primary chamber of the master cylinder.
- Fit one end of vinyl tube into air bleeder and put the other end into a brake fluid containe...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Legacy BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Legacy AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Legacy cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 1997 Subaru Legacy L 2.2 H4 GAS
The brake booster is located inline between the master cylinder and the brake pedal. It serves to mechanically boost the force pushing the pistons of the master cylinder.
The brake booster consists of a power cylinder section and a power piston section. The power cylinder is made up of a front shell, rear shell and a diaphragm. The front and rear shells are connected with the diaphragm placed in between the two. The power cylinder chamber is closed to the atmosphere and the left and right chambers of the diaphragm are kept sealed.
The power piston is ...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Legacy BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Subaru Legacy AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Subaru Legacy cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 1997 Subaru Legacy Limited 2.5 H4 GAS
The brake booster is located inline between the master cylinder and the brake pedal. It serves to mechanically boost the force pushing the pistons of the master cylinder.
The brake booster consists of a power cylinder section and a power piston section. The power cylinder is made up of a front shell, rear shell and a diaphragm. The front and rear shells are connected with the diaphragm placed in between the two. The power cylinder chamber is closed to the atmosphere and the left and right chambers of the diaphragm are kept sealed.
The power piston is ...
CLICK HERE TO GET FULL ACCESS TO 1997 Subaru Legacy BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1997 Subaru Legacy vehicle.
|
| Access the Complete guide! |
