Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1997 Eagle Vision car and truck
repair procedures including Eagle engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1997 Eagle Vision automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1997 Eagle Vision
- 1997 Eagle Vision ESI 3.3 V6 GAS, CID:201, Fuel Injection, Aspiration:201, Engine VIN:, Desg:T
- 1997 Eagle Vision ESI 3.5 V6 GAS, CC:3497, CID:215, Fuel Injection, Aspiration:215, Engine VIN:, Desg:F
- 1997 Eagle Vision TSI 3.5 V6 GAS, CC:3497, CID:215, Fuel Injection, Aspiration:215, Engine VIN:, Desg:F
BRAKE SERVICE PROCEDURES FOR 1997 Eagle Vision AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Eagle Vision cars and light trucks from 1990+.
Disc Brakes -> Type 5-Kelsey-Hayes Dual Pin Floating Caliper Disc Brake, Rear -> Caliper Service -> Overhaul -> Replacement
Vehicle: 1997 Eagle Vision TSI 3.5 V6 GAS
Replacement
- Raise and support vehicle.
- Remove rear wheel and tire assembly.
- Remove two caliper assembly to adapter guide pin bolts.
- Remove caliper from adapter as follows:
- Rotate top of caliper away from adapter.
- Lift caliper off bottom abutment on adapter.
- Support caliper assembly from rear strut to prevent flexible brake hose damage.
- Remove rear rotor from hub by pulling it straight off wheel mounting studs.
Overhaul
- Remove caliper from rotor as described under "Brake Pad Service."
- Place a small piece of wood between piston and caliper fingers, then carefully depress brake pedal to hydraul...
CLICK HERE TO GET FULL ACCESS TO 1997 Eagle Vision BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Eagle Vision AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Eagle Vision cars and light trucks from 1990+.
Anti-Lock Brakes -> Type 1-Teves Mark IV Anti-Lock Braking System -> Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation
Vehicle: 1997 Eagle Vision ESI 3.5 V6 GAS
Accessing Diagnostic Trouble Codes
To enter diagnostic mode, vehicle speed must be below 10 mph. If vehicle speed is above 10 mph, a "No Response" message will be displayed on the DRB II. The following are characteristics of diagnostic mode.
- The amber anti-lock warning lamp and brake warning lamp will flash.
- If a hard fault, such as an inlet or outlet valve fault or main relay/power circuit failure fault, is present, these lamps will illuminate without blinking and no diagnostic operations will be avail...
CLICK HERE TO GET FULL ACCESS TO 1997 Eagle Vision BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Eagle Vision AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Eagle Vision cars and light trucks from 1990+.
Power Brake Units -> Troubleshooting -> Decreasing Brake Pedal Travel -> Dragging Brakes -> Hard Brake Pedal
Vehicle: 1997 Eagle Vision ESI 3.5 V6 GAS
Decreasing Brake Pedal Travel
If a decreasing brake pedal is encountered, the power brake unit may be binding internally. To test the power brake unit for this condition proceed as follows:
- Place transmission shift lever into Neutral and start engine.
- Increase engine speed to approximately 1500 RPM, close throttle and completely depress brake pedal.
- Slowly release brake pedal and stop engine.
- Remove vacuum check valve and hose from power brake unit. Observe for backward movement of brake pedal.
- If brake pedal moves backward, power brake unit has internal binding. Replace power brake u...
CLICK HERE TO GET FULL ACCESS TO 1997 Eagle Vision BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Eagle Vision AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Eagle Vision cars and light trucks from 1990+.
Disc Brakes -> Type 4-Kelsey-Hayes Dual Pin Floating Caliper Disc Brake, Front -> Brake System Bleed -> Manual Bleed -> Pressure Bleed
Vehicle: 1997 Eagle Vision ESI 3.5 V6 GAS
Bleeding the hydraulic brake system is necessary if air has entered the system. Symptoms can be noted by loss of brake operation, and/or a low or spongy brake pedal.
The hydraulic fluid is bled or flushed from the system through bleeder valves located on the calipers, wheel cylinders, and some master cylinders. Use ...
CLICK HERE TO GET FULL ACCESS TO 1997 Eagle Vision BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Eagle Vision AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Eagle Vision cars and light trucks from 1990+.
Drum Brakes -> Type 1: Kelsey-Hayes & Varga Leading-Trailing Drum Brakes -> Inspection -> Adjuster Mechanism -> Backing Plate -> Brake Drums -> Brake Linings & Springs -> Parking Brake Cable -> Wheel Cylinder
Vehicle: 1997 Eagle Vision ESI 3.5 V6 GAS
Brake Drums
Any time the brake drums are removed for brake service, the braking surface diameter should be inspected with a suitable brake drum micrometer at several points to determine if they are within the safe oversize limit stamped on the brake drum outer surface. If the braking surface diameter exceeds specifications, the drum must be replaced. If the braking surface diameter is within specifications, drums should be cleaned and inspected for cracks, scores, deep grooves, taper, out of round and heat spotting. If drums are cracked or heat spotted, they must be replaced. Scoring ...
CLICK HERE TO GET FULL ACCESS TO 1997 Eagle Vision BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Eagle Vision AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Eagle Vision cars and light trucks from 1990+.
Anti-Lock Brakes -> Type 1-Teves Mark IV Anti-Lock Braking System -> Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation
Vehicle: 1997 Eagle Vision ESI 3.3 V6 GAS
Accessing Diagnostic Trouble Codes
To enter diagnostic mode, vehicle speed must be below 10 mph. If vehicle speed is above 10 mph, a "No Response" message will be displayed on the DRB II. The following are characteristics of diagnostic mode.
- The amber anti-lock warning lamp and brake warning lamp will flash.
- If a hard fault, such as an inlet or outlet valve fault or main relay/power circuit failure fault, is present, these lamps will illuminate without blinking and no diagnostic operations will be avail...
CLICK HERE TO GET FULL ACCESS TO 1997 Eagle Vision BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1997 Eagle Vision vehicle.
|
| Access the Complete guide! |
