Auto Parts Search
We have info for following modifications of 1996 Ford Probe
- 1996 Ford Probe GT 2.5 V6 GAS, CC:2450, CID:152, Fuel Injection, Aspiration:152, Engine VIN:, Desg:B
- 1996 Ford Probe SE 2.0 L4 GAS, CC:1989, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:A
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Low Oil Level Warning Indicator ->
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
This system is used to indicate when the engine oil level is 11/2 quarts or more below the specified level. The lamp should light during engine starting. If the oil level is sufficient, the lamp will go off when the engine is operating. If the ...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Low Oil Level Warning Indicator ->
Vehicle: 1996 Ford Probe GT 2.5 V6 GAS
This system is used to indicate when the engine oil level is 11/2 quarts or more below the specified level. The lamp should light during engine starting. If the oil level is sufficient, the lamp will go off when the engine is operating. If the ...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Low Coolant Lamp ->
Vehicle: 1996 Ford Probe GT 2.5 V6 GAS
The low coolant warning lamp should light whenever the coolant level in the coolant recovery bottle is 1/4 to 3/4 inch or more below the cold full mark. Raise coolant level in recovery bottle to the cold full mark to turn lamp off.
On models equipped with GEM module and low coolant level warning system, t...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Electronic Throttle Control ->
Vehicle: 1996 Ford Probe GT 2.5 V6 GAS
Electronic throttle displays when the system has malfunctioned and the engine has defaulted to a limp-home operation. On vehicles equipped with ...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Powertrain Malfunction Indicator ->
Vehicle: 1996 Ford Probe GT 2.5 V6 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected in the powertrain system. If the lamp remains On a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Powertrain Malfunction Indicator will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Service Interval Reminder -> Probe -> Electronic Instrument Cluster -> Vehicle Maintenance Monitor
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
Electronic Instrument Cluster
At 7500 mile intervals, a Service Check message will be displayed under the System Scanner nomenclature on the instrument cluster for 3 minutes after engine starts, Fig. . After performing the required interval service, reset the service interval by depressing and holding the Service reset button, located on the speed alarm keyboard, until three tones have sounded, Fig. .
Vehicle Maintenance Monitor
At 7500 mile intervals ...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1996 Ford Probe vehicle. |
Access the Complete guide! |