Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1992 Saab 9000 car and truck
repair procedures including Saab engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1992 Saab 9000 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1992 Saab 9000
- 1992 Saab 9000 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:B
- 1992 Saab 9000 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:M
- 1992 Saab 9000 CD 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:B
- 1992 Saab 9000 CD 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:M
- 1992 Saab 9000 S 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:B
- 1992 Saab 9000 Griffin Edtion 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:M
BRAKE SERVICE PROCEDURES FOR 1992 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Saab 9000 cars and light trucks from 1990+.
ANTI-LOCK BRAKE SYSTEM -> Anti-Lock Brake System w/Traction Control System -> TROUBLESHOOTING
Vehicle: 1992 Saab 9000 Griffin Edtion 2.3 L4 GAS
This Anti-Lock Brake System Applies Only To 1992 9000 Models With Manual Transmissions.
- The diagnostic socket (green) is located below the righthand front seat.
- During fault diagnosis, the ignition switch must always be in the On position.
- The ISAT system number for the TC/ABS system is number 3.
- Always read off and note down all stored fault codes before disconnecting the battery or ECU.
- If communication cannot be established between ISAT and the ECU, check the leads between ECU pins 23 and 42 and the diagnostic socket. Also check that the power feed and ground circuits to the diagn...
CLICK HERE TO GET FULL ACCESS TO 1992 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Saab 9000 cars and light trucks from 1990+.
SAAB, HYDRAULIC BRAKE SYSTEMS -> MASTER CYLINDER OVERHAUL -> ASSEMBLE -> DISASSEMBLE
Vehicle: 1992 Saab 9000 2.3 L4 GAS
When working on any hydraulic brake components it is extremely important to keep the work area clean. Clean any parts that are to be reused with new brake fluid or a cleaning fluid specifically designed for hydraulic components. Wipe all parts dry using clean lint-free paper or cloth. Gaskets, seals, O-rings and rubber components should not be reused. Prior to assembly, all components should be generously lubricated with clean brake fluid.
DISASSEMBLE
- Clamp master cylinder in a soft-jaw vice.
- Remove rubber seals from brake hose connections.
- Carefully push primary plunger up...
CLICK HERE TO GET FULL ACCESS TO 1992 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Saab 9000 cars and light trucks from 1990+.
SAAB, HYDRAULIC BRAKE SYSTEMS -> BLEEDING SYSTEM
Vehicle: 1992 Saab 9000 CD 2.3 L4 GAS
- Ensure brake fluid reservoir is full.
- Connect a transparent hose to bleed nipple of brake caliper.
- Place other end of hose into a clear container.
- Depress brake pedal, then open bleed nipple. Close nipple as soon as the pedal reach...
CLICK HERE TO GET FULL ACCESS TO 1992 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Saab 9000 cars and light trucks from 1990+.
ANTI-LOCK BRAKE SYSTEM -> Anti-Lock Brake System w/Traction Control System -> COMPONENT DESCRIPTION -> ELECTRONIC CONTROL UNIT (TC/ABS ECU) -> TC/ABS HYDRAULIC UNIT -> TCS VALVE BLOCK
Vehicle: 1992 Saab 9000 CD 2.3 L4 GAS
This Anti-Lock Brake System Applies Only To 1992 9000 Models With Manual Transmissions.
ELECTRONIC CONTROL UNIT (TC/ABS ECU)
The ECU is programmed to detect both permanent and intermittent faults. Faults detected by the ECU are stored in an EEPROM chip, so the fault codes remain in memory even when power supply is switched off or interrupted.
TC/ABS HYDRAULIC UNIT
The main components of the hydraulic unit, Fig. , are the brake fluid reservoir, fluid level switch, accumulator and a pressure warning switch.
TCS VALVE BLOCK
In contrast to the conventional ABS unit. the TC/ABS ...
CLICK HERE TO GET FULL ACCESS TO 1992 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Saab 9000 cars and light trucks from 1990+.
ANTI-LOCK BRAKE SYSTEM -> Anti-Lock Brake Systems Less Traction Control -> SYSTEM SERVICE -> 1990-92 9000 -> 1990-92 9000 Models -> 900 -> 900 Models -> 9000 -> ACCUMULATOR, REPLACE -> BLEEDING BRAKES -> BRAKE FLUID RESERVOIR, REPLACE -> ECU, REPLACE -> Front -> HYDRAULIC UNIT, REPLACE -> PRESSURE SWITCH, REPLACE -> PUMP & MOTOR UNIT, REPLACE -> PUMP DELIVERY LINE, REPLACE -> Rear -> VALVE BLOCK, REPLACE -> WHEEL SENSORS, REPLACE
Vehicle: 1992 Saab 9000 Griffin Edtion 2.3 L4 GAS
BRAKE FLUID RESERVOIR, REPLACE
- Remove accumulator as described in "Accumulator, Replace."
- Remove hydraulic unit as described in "Hydraulic Unit, Replace."
- Disconnect pump inlet hose from brake fluid reservoir, then remove reservoir to hydraulic unit attaching screw.
- Lift reservoir off hydraulic unit, then remove rubber bushings from hydraulic unit. Take care not to lose spacer and O-ring on rear connection.
- Reverse procedure to install, noting the following:
- Install two new rubber bushings into hydraulic unit.
- Bleed brake system as described in "Bleeding Brakes."
- Switch ignition on and ensure ...
CLICK HERE TO GET FULL ACCESS TO 1992 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Saab 9000 cars and light trucks from 1990+.
ANTI-LOCK BRAKE SYSTEM -> Anti-Lock Brake System w/Traction Control System -> DIAGNOSIS & TESTING -> Anti-Lock Light -> Brake Fluid Light -> COMMAND CODES -> FAULT (TROUBLE) CODE 3/22251 -> FAULT (TROUBLE) CODE 3/25321 -> FAULT (TROUBLE) CODE 36521 -> FAULT (TROUBLE) CODE 36522 -> FAULT (TROUBLE) CODE 5/33421 -> FAULT (TROUBLE) CODE 5/33422 -> FAULT (TROUBLE) CODE 5/33423 -> FAULT (TROUBLE) CODE 5/33424 -> FAULT (TROUBLE) CODE 5/33425 -> FAULT (TROUBLE) CODE 5/33426 -> FAULT (TROUBLE) CODE 5/33427 -> FAULT (TROUBLE) CODE 5/33428 -> FAULT (TROUBLE) CODE 5/33429 -> FAULT (TROUBLE) CODE 775B1 -> FAULT (TROUBLE) CODE 775B2 -> FAULT (TROUBLE) CODE E/F7061 -> FAULT (TROUBLE) CODES -> FAULT (TROUBLE) CODES 234B1, 234B2, 234B3 & 234B4 -> FAULT (TROUBLE) CODES 4/24221, 2422A, 24251 & 24291 -> FAULT (TROUBLE) CODES 4/24222, 2422B, 24252 & 24292 -> FAULT (TROUBLE) CODES 4/24223, 2422C, 24253 & 24293 -> FAULT (TROUBLE) CODES 4/24224, 2422D, 24254 & 24294 -> Less ISAT Tester -> Open Circuit -> Resistance Checks -> Short To +12V -> Short To Ground -> TC/ABS CONTROL UNIT PIN TESTS -> TCS CTRL Light -> TCS Light -> Voltage Checks -> WARNING & INDICATOR LIGHTS -> With ISAT Tester
Vehicle: 1992 Saab 9000 S 2.3 L4 GAS
This Anti-Lock Brake System Applies Only To 1992 9000 Models With Manual Transmissions.
COMMAND CODES
Command codes instruct the ECU to perform certain functions while diagnosing fault codes.
Refer to Fig. , for ISAT command codes.
FAULT (TROUBLE) CODES
The ECU connector on the wiring loom is in the form of a moulded plug, test probes cannot be connected to the back of the connector.
Use breakout box 8611006 with test lead set 8611030, which should be connected between the ECU and the connector.
All measurements on the system must be made with breakout box connected.
To access fault...
CLICK HERE TO GET FULL ACCESS TO 1992 Saab 9000 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1992 Saab 9000 vehicle.
|
| Access the Complete guide! |
