Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1992 Hyundai Sonata car and truck
repair procedures including Hyundai engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1992 Hyundai Sonata automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1992 Hyundai Sonata
- 1992 Hyundai Sonata 3.0 V6 GAS, CC:2972, Fuel Injection, Engine VIN:, Desg:T
- 1992 Hyundai Sonata 2.0 L4 GAS, CC:1997, Fuel Injection, Engine VIN:, Desg:F
- 1992 Hyundai Sonata GL 3.0 V6 GAS, CC:2972, Fuel Injection, Engine VIN:, Desg:T
- 1992 Hyundai Sonata GL 2.0 L4 GAS, CC:1997, Fuel Injection, Engine VIN:, Desg:F
- 1992 Hyundai Sonata GLS 3.0 V6 GAS, CC:2972, Fuel Injection, Engine VIN:, Desg:T
- 1992 Hyundai Sonata GLS 2.0 L4 GAS, CC:1997, Fuel Injection, Engine VIN:, Desg:F
BRAKE SERVICE PROCEDURES FOR 1992 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Hyundai Sonata cars and light trucks from 1990+.
HYUNDAI, HYDRAULIC BRAKE SYSTEM -> BRAKE BOOSTER PUSH ROD CLEARANCE -> SCOUPE -> SONATA LESS BENDIX SYSTEM
Vehicle: 1992 Hyundai Sonata GL 3.0 V6 GAS
SONATA LESS BENDIX SYSTEM
- Measure dimensions A as shown in Fig. .
- Brake booster push rod clearance, dimension A, should be 1.470-1.482 inch at 191/2 inches Hg of vacuum. If not withi...
CLICK HERE TO GET FULL ACCESS TO 1992 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Hyundai Sonata cars and light trucks from 1990+.
HYUNDAI, ANTI-LOCK BRAKES -> DIAGNOSIS & TESTING -> BASIC DIAGNOSIS -> DESCRIPTION -> DIAGNOSIS USING SELF-DIAGNOSTIC MODE -> INITIAL CHECK -> SYSTEM CIRCUIT INSPECTION
Vehicle: 1992 Hyundai Sonata GL 2.0 L4 GAS
DESCRIPTION
If a malfunction occurs, the diagnostic system will identify the problem and the ECU will store the codes. At the same time, the system informs the driver of a malfunction with the ABS warning lamp.
INITIAL CHECK
Start engine and drive at a speed of 3-6 mph, then verify that the modulator is operating by listening for motor pump hum and solenoid clicking for 1 or 2 seconds. Procedure should be performed within first three minutes after start up. Solenoid valve and motor pump cycling takes place between 3 and 6 mph, as long as brake is not applied.
BASIC DIAGNOSIS
- Chec...
CLICK HERE TO GET FULL ACCESS TO 1992 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Hyundai Sonata cars and light trucks from 1990+.
HYUNDAI, ANTI-LOCK BRAKES -> COMPONENT REPLACEMENT -> ELECTRONIC CONTROL UNIT (ECU) -> Front Wheel Sensors -> MODULATOR -> Rear Wheel Sensors -> SENSORS
Vehicle: 1992 Hyundai Sonata GLS 2.0 L4 GAS
ELECTRONIC CONTROL UNIT (ECU)
- Disconnect ECU electrical connector, then remove mounting bolts and washers, Fig. .
- Remove ECU from vehicle.
- Reverse procedure to install.
MODULATOR
- Drain master cylinder by opening caliper bleed screws, refer to "Bleeding System."
- Remove any remaining fluid with a syringe, then disconnect six brake lines from modulator.
- Remove mounting bolts and washers, then the modulator.
- R...
CLICK HERE TO GET FULL ACCESS TO 1992 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Hyundai Sonata cars and light trucks from 1990+.
HYUNDAI -> Disc Brakes -> CALIPER SERVICE -> Assembly -> Disassembly -> ELANTRA & SONATA -> EXCEL & SCOUPE -> FRONT -> Installation -> REAR -> Removal
Vehicle: 1992 Hyundai Sonata GL 2.0 L4 GAS
EXCEL & SCOUPE
Removal
- Remove brake pads as described previously.
- Disconnect and cap brake line(s).
- Remove caliper attaching bolts and caliper assembly from steering knuckle.
Disassembly
- Remove sleeve, sleeve boot and pin boots, Fig. .
- Protect fingers with shop towel, then blow piston from caliper bore with compressed air.
- Remove piston boot, then pry piston seal from caliper bore using a suitable screwdriver.
Assembly
- Clean all components with suitable cleaner.
- Inspect caliper bore, piston and carrier for damage or excessive wear.
- Apply rubber grease to new piston seal, then install piston...
CLICK HERE TO GET FULL ACCESS TO 1992 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Hyundai Sonata cars and light trucks from 1990+.
HYUNDAI, POWER BRAKE UNITS -> POWER BRAKE BOOSTER REPLACEMENT
Vehicle: 1992 Hyundai Sonata GL 2.0 L4 GAS
- Remove master cylinder, refer to "Master Cylinder, Replace" in "Hydraulic Brake System".
- Disconnect vacuum hose.
- From inside vehicle, se...
CLICK HERE TO GET FULL ACCESS TO 1992 Hyundai Sonata BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Hyundai Sonata AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1992 Hyundai Sonata cars and light trucks from 1990+.
HYUNDAI, HYDRAULIC BRAKE SYSTEM -> MASTER CYLINDER REPLACEMENT -> EXCEPT SCOUPE & SONATA w/BENDIX SYSTEM -> SCOUPE & SONATA w/BENDIX SYSTEM
Vehicle: 1992 Hyundai Sonata GLS 3.0 V6 GAS
EXCEPT SCOUPE & SONATA w/BENDIX SYSTEM
- Disconnect electrical connector from fluid level switch, if equipped, Figs. through .
- Disconnect brake lines from master cylinder and plug open ports.
- Remove master cylinder mounting nuts, disconnect proportioning valve mounting bracket, if equipped, then remove master cylinder from vehicle.
- Reverse procedure to install, noting the following:
- Tighten master cylinder mounting nuts and brake lines to specifications.
- On 1989 Excel and Sonat...
CLICK HERE TO GET FULL ACCESS TO 1992 Hyundai Sonata BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1992 Hyundai Sonata vehicle.
|
| Access the Complete guide! |
