Auto Parts Search
1992 Chevrolet Corvette CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Chevrolet REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1992 Chevrolet Corvette car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Chevrolet Corvette automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR 1992 Chevrolet Corvette AUTOMOBILES
Cooling Fans -> Passenger Cars Except Saturn -> EIGHTY EIGHT & NINETY EIGHT -> Both Coolant Fans Do Not Run -> COMPONENT REPLACEMENT -> Coolant Fan, Replace -> Coolant Fans Do Not Operate In High Speed With A/C Head Pressure Above 210 psi -> DESCRIPTION -> Lefthand Coolant Fan Does Not Operate In High Speed -> Lefthand Coolant Fan Does Not Operate In Low Speed -> Lefthand Coolant fan Runs Continuously In High Speed With Ignition Switch At RUN, Engine Coolant Cool & A/C Off -> Lefthand Coolant Fan Runs Continuously In Low Speed With Ignition Switch At RUN, Engine Coolant Cool & A/C Off -> System Check -> System Diagnosis -> SYSTEM DIAGNOSIS & TESTING -> TROUBLESHOOTING
Vehicle: 1992 Chevrolet Corvette 5.7 V8 GAS
DESCRIPTION
Two coolant fans, wired in parallel, operate whenever cooling is required.
The powertrain control module (PCM) has two coolant fan control terminals: one for high speed and one for low speed. When the PCM's low speed control closes at connector C3, terminal C4, it grounds the low speed coolant relay coil. When the ignition switch is in the RUN position and the relay contacts close, voltage is supplied to the coolant fans. The coolant fan resistors drop the voltage to the lefthand coolant fan, causing it to run in low speed. The righthand c...
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Chevrolet Corvette AUTOMOBILES
Power Brake Units -> Troubleshooting -> AC-DELCO TANDEM DIAPHRAGM TYPE -> BCIA SINGLE & TANDEM DIAPHRAGM TYPE -> Brakes Drag -> Brakes Grab -> Brakes Slow To Release Or Drag -> Brakes Slow To Respond -> Excessive Pedal Effort -> Hard Pedal -> Hard Pedal/Brakes Inefficient -> Low Or Spongy Brake Pedal -> Slow Or No Release -> TOYOTA/GM SINGLE DIAPHRAGM TYPE
Vehicle: 1992 Chevrolet Corvette ZR-1 5.7 V8 GAS
AC-DELCO TANDEM DIAPHRAGM TYPE
Hard Pedal
- Internal vacuum leak.
- Faulty control valve.
Brakes Grab
- Faulty control valve.
Slow Or No Release
- Faulty pushrod adjustment.
- Bind in linkage.
BCIA SINGLE & TANDEM DIAPHRAGM TYPE
Brakes Grab
- Internal vacuum leak.
- Faulty control valve
Excessive Pedal Effort
- Leak in booster vacuum supply.
- Glazed linings.
- Contaminated brake fluid.
- Restricted filter or booster valve air passage.
- Leak in booster vacuum supply.
- Damaged booster or improperly assembled booster valve.
Brakes Slow To Respond
- Restricted filter or booster valve air passage.
- Contaminated brake fluid.
- Leak in...
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1992 Chevrolet Corvette AUTOMOBILES
General Motors Corp./Saturn Passenger Cars -> Fuel Pressure Relief -> Except Aveo, LaCrosse, LeMans (1988-93), Malibu & Malibu Maxx (2004-05), Metro, Nova, Prizm, Spectrum & Storm -> Engine Fuel Pressure Service Port -> Engines Less Fuel Pressure Service Port
Vehicle: 1992 Chevrolet Corvette ZR-1 5.7 V8 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
After the battery has been disconnected and reconnected, some abnormal driveability symptoms may occur. The vehicle may need to be driven while the vehicle relearns its adaptive strateg...
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1992 Chevrolet Corvette AUTOMOBILES
DRIVESHAFT, Replace -> Axle Shaft -> Propeller Shaft
Vehicle: 1992 Chevrolet Corvette ZR-1 5.7 V8 GAS
Propeller Shaft
- With transmission in neutral and parking brake released, raise and support vehicle, then remove underbody braces, as required.
- Remove exhaust system as follows:
- Disconnect AIR pipe from catalytic converter and exhaust pipe.
- Disconnect electrical connector to oxygen sensor.
- Remove bolts securing muffler to hangers, disconnect exhaust pipes from manifolds and remove exhaust system as an assembly.
- Support transmission, remove support beam retaining bolts and support beam.
- Mark position of shaft in relation to pinion flange for installation.
- Remove straps securing univer...
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 1992 Chevrolet Corvette AUTOMOBILES
Description
Vehicle: 1992 Chevrolet Corvette ZR-1 5.7 V8 GAS
The TPMS (Tire Pressure Monitoring System) will inform the vehicle operator of and under inflated tire condition. The system allows the tire pressure in all four tires to monitored. The sensors will transmit allow tire message if a tire pressure falls below 25 psi.
The vehicle must be traveling 25 mph for 30...
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1992 Chevrolet Corvette AUTOMOBILES
Starter, Replace
Vehicle: 1992 Chevrolet Corvette ZR-1 5.7 V8 GAS
If shims are required between starter and engine block, they should be placed in their original location during installation. If starter is noisy during cranking, remove one .015 inch double shim or add one .015 single shim to outer bolt. If starter makes a high pitched whine after firing, add .015 inch double shims until noise ceases.
- Disconnect battery ground cable.
- Drain cooling system into a suita...
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1992 Chevrolet Corvette AUTOMOBILES
General Motors Corp./Saturn Cars -> Check Gauge Warning Lamp ->
Vehicle: 1992 Chevrolet Corvette 5.7 V8 GAS
The Check Gauge warning lamp will light to warn the driver to inspect the oil pressure gauge, engine coolant temperature ga...
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1992 Chevrolet Corvette AUTOMOBILES
Radiator, Replace
Vehicle: 1992 Chevrolet Corvette ZR-1 5.7 V8 GAS
- Disconnect battery ground cable.
- Drain coolant from radiator.
- Remove upper radiator support, Fig. .
- Disconnect radiator inlet and outlet hoses at radiator.
- On models equipped with automatic transmission,disconnect transmission oil c...
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1992 Chevrolet Corvette AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1992 Chevrolet Corvette 5.7 V8 GAS
- Loosen accessory drive belt tensioners No. 3 and 10 in to reduce tension on accessory drive belts.
- Remove accessory drive belts.
- Clean accessory drive belt sur...
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1992 Chevrolet Corvette AUTOMOBILES
Component location diagrams for most 1992 Chevrolet Corvette cars and light trucks sold in the U.S. from 1990+.
 RH Rear Of Engine Compartment Diagram for 1992 Chevrolet Corvette 5.7 V8 GASComponents on diagram: |
 RH Front Corner Of Engine Compartment Diagram for 1992 Chevrolet Corvette ZR-1 5.7 V8 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1992 Chevrolet Corvette AUTOMOBILES
OEM drawn wiring diagrams for most 1992 Chevrolet Corvette cars and light trucks sold in the U.S.
 1992 Chevrolet Corvette 5.7 V8 GAS Wiring DiagramComponents on diagram: |
 1992 Chevrolet Corvette 5.7 V8 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1992 Chevrolet Corvette AUTOMOBILES
OEM TSB listings for most 1992 Chevrolet Corvette cars and light trucks sold in the U.S. from 1985+.
|
Document: Car and Truck Fix It Right the First Time Issues Vehicle: 1992 Chevrolet Corvette 5.7 V8 GAS Auto Systems: |
|
Document: GM TIRE WARRANTY PROGRAM CLAIMS GOODWILL GUIDELINES - REVISED Vehicle: 1992 Chevrolet Corvette 5.7 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1992 Chevrolet Corvette AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1992 Chevrolet Corvette cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1992 Chevrolet Corvette cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1992 Chevrolet Corvette cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1992 Chevrolet Corvette cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1992 Chevrolet Corvette SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1992 Chevrolet Corvette vehicle.
|
| Access the Complete guide! |
