Auto Parts Search
We have info for following modifications of 2009 KIA RIO
- 2009 KIA RIO 1.6 L4 GAS, CC:1599, Fuel Injection, Engine VIN:, Desg:3
- 2009 KIA RIO LX 1.6 L4 GAS, CC:1599, Fuel Injection, Engine VIN:, Desg:3
- 2009 KIA RIO SX 1.6 L4 GAS, CC:1599, Fuel Injection, Engine VIN:, Desg:3
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA RIO AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA RIO cars and light trucks sold in the U.S. from mid 1990's+.
Reset Procedures
Vehicle: 2009 KIA RIO 1.6 L4 GAS
The Low Tire Pressure Warning lamp will illuminate for approximately three seconds as a bulb check when the ignition switch is placed in the On position. This system uses radio frequency pressure sensors which mon...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA RIO TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA RIO AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA RIO cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Installation -> Removal -> Tire Pressure Sensor -> TPMS Receiver
Vehicle: 2009 KIA RIO 1.6 L4 GAS
Tire Pressure Sensor
Removal
- Loosen the wheel lug nuts.
- Raise and support the vehicle with jack stands.
- Remove tire and wheel assembly from vehicle.
- Deflate air from tire assembly, then remove wheel weights.
- Break tire bead 90° from valve stem. When removing tire from rim caution should be taken not to hit valve stem with tire tools.
- Remove the valve nut. Use caution when handling sensor.
- Discard valve nut and valve assembly.
Installation
- Use caution when handling sensor. Avoid getting any lubricant on sensor.
- Slide sensor through valve hole in the rim.
- Hold the sensor against the rim...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA RIO TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA RIO AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA RIO cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Identification
Vehicle: 2009 KIA RIO LX 1.6 L4 GAS
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to DLC (Data Link Connector) and follow manufacturer's instructions.
Diagnostic Trouble Code Identification
...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA RIO TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA RIO AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA RIO cars and light trucks sold in the U.S. from mid 1990's+.
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2009 KIA RIO LX 1.6 L4 GAS
Refer to Fig. for wirin...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2009 KIA RIO TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA RIO AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA RIO cars and light trucks sold in the U.S. from mid 1990's+.
Component Locations
Vehicle: 2009 KIA RIO 1.6 L4 GAS
Refer to F...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA RIO TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 KIA RIO AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2009 KIA RIO cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures -> Tire Pressure Sensor Initiation -> TPMS Receiver
Vehicle: 2009 KIA RIO 1.6 L4 GAS
Tire Pressure Sensor Initiation
- Using Kia TPMS exciter tool, or equivalent, read the four tire pressure sensor IDs starting with sensor 1 the LH front wheel.
- Read the remaining sensors in the following order:
- Sensor 2, RH front wheel.
- Sensor 3, LH rear wheel.
- Sensor 4, RH rear wheel.
- Connect the Kia exciter tool, or equivalent, to the DLC (Data Link Connector) located under the LH side of the instrument panel.
- Using the tool, register the four sensor IDs to the TPMS receiver.
- Disconnect the tool from the DLC.
- Place the ignition switch in the Off position for 15 seconds, then turn the ...
CLICK HERE TO GET FULL ACCESS TO 2009 KIA RIO TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2009 KIA RIO vehicle. |
Access the Complete guide! |