Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 Jeep Commander car and truck
repair procedures including Jeep engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2009 Jeep Commander automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2009 Jeep Commander
- 2009 Jeep Commander Limited 4.7 V8 GAS, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
- 2009 Jeep Commander Limited 4.7 V8 FLEX, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
- 2009 Jeep Commander Limited 5.7 V8 GAS, CID:345, Fuel Injection, Aspiration:345, Engine VIN:, Desg:T
- 2009 Jeep Commander Overland 5.7 V8 GAS, CID:345, Fuel Injection, Aspiration:345, Engine VIN:, Desg:T
- 2009 Jeep Commander Sport 4.7 V8 GAS, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
- 2009 Jeep Commander Sport 3.7 V6 GAS, CID:226, Fuel Injection, Aspiration:226, Engine VIN:, Desg:K
- 2009 Jeep Commander Sport 4.7 V8 FLEX, CID:285, Fuel Injection, Aspiration:285, Engine VIN:, Desg:N
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> All Wheel Drive (AWD) Warning Lamp ->
Vehicle: 2009 Jeep Commander Sport 4.7 V8 GAS
This light monitors the AWD system. The light will turn on for a bulb check when the ignition switch is turned to the on position and may stay on for as long as three seconds. When the lamp is illuminated solid here is an A...
CLICK HERE TO GET FULL ACCESS TO 2009 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> All Wheel Drive (AWD) Warning Lamp ->
Vehicle: 2009 Jeep Commander Limited 4.7 V8 GAS
This light monitors the AWD system. The light will turn on for a bulb check when the ignition switch is turned to the on position and may stay on for as long as three seconds. When the lamp is illuminated solid here is an A...
CLICK HERE TO GET FULL ACCESS TO 2009 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Electronic Throttle Control Indicator ->
Vehicle: 2009 Jeep Commander Limited 5.7 V8 GAS
When the ignition is turned On, the lamp will light for approximately 6-12 seconds as a bulb inspection. If the lamp is illuminated with the engine running, the vehicle is usually drivable but the electronic throttle system must be diagnosed and servic...
CLICK HERE TO GET FULL ACCESS TO 2009 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Check Engine Lamp -> Chrysler, Dodge, Jeep & Plymouth Except Ram 50
Vehicle: 2009 Jeep Commander Limited 5.7 V8 GAS
On models less OBD II, the Check Engine lamp should light for approximately 3 seconds after the ignition has been turned On as a bulb inspection. If improper or no signals are received by the Powertrain Control Module (PCM) from various sensors and monitored systems or if the PCM enters its Limp-In mode, the PCM will light the Check Engine lamp. On Chrysler, Dodge and Plymouth models, After diagnosing and servicing the vehicle, the PCM memory will be cleared after approximately 40 to 100 ignition key On-Off cycles or by using a suitable scan tool. ...
CLICK HERE TO GET FULL ACCESS TO 2009 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Anti-Lock Brake System Warning Lamp -> Jeep
Vehicle: 2009 Jeep Commander Limited 4.7 V8 GAS
Red and yellow indicator lamps are used to warn of system faults. The red lamp warns of such faults as low brake fluid level, parking brake On, system pressure differential and other system faults. The red indicator lamp should light for approximately two seconds during engine starting and should go off, unless parking brake is applied or a problem in the brake system exist. The red indicator lamp should reset after repairs to system have been completed and system has returned to normal o...
CLICK HERE TO GET FULL ACCESS TO 2009 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Jeep Commander AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Jeep Commander cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Trucks -> Anti-Lock Brake System Warning Lamp -> Jeep
Vehicle: 2009 Jeep Commander Limited 5.7 V8 GAS
Red and yellow indicator lamps are used to warn of system faults. The red lamp warns of such faults as low brake fluid level, parking brake On, system pressure differential and other system faults. The red indicator lamp should light for approximately two seconds during engine starting and should go off, unless parking brake is applied or a problem in the brake system exist. The red indicator lamp should reset after repairs to system have been completed and system has returned to normal o...
CLICK HERE TO GET FULL ACCESS TO 2009 Jeep Commander MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2009 Jeep Commander vehicle.
|
| Access the Complete guide! |
