Auto Parts Search
We have info for following modifications of 2008 Scion TC
- 2008 Scion TC 2.4 L4 GAS, CC:2398, Fuel Injection
- 2008 Scion TC Spec 2.4 L4 GAS, CC:2398, Fuel Injection
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from 1990+.
Scion -> Tire Pressure Monitoring System (TPMS) Warning Indicator -> 2008 tC -> Initialization -> Registration -> Relearn -> Reset -> System Initialization -> Tire Pressure Sensor & Transmitter -> TPMS ECU
Vehicle: 2008 Scion TC 2.4 L4 GAS
Reset
When the ignition switch is placed in the on position, the TPMS (Tire Pressure Monitoring System) warning lamp will illuminate for approximately 3 seconds and then go off as a bulb check. This warning lamp will illuminate when tire pressure falls below a specified psi. When the warning lamp illuminates, check the air pressure of the tire and adjust it to specified pressure. When the vehicle is driven more than 18 mph after the adjustment, the lamp will go off.
Relearn
Registration
TPMS ECU
If replacing the TPMS ECU, prior to removal, use a suitably programmed scan tool to read the regi...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from 1990+.
Scion -> Air Bag Warning Lamp ->
Vehicle: 2008 Scion TC 2.4 L4 GAS
- Connect two service wires to terminals Tc and CG of DLC3 (Data Link Connector), then place ignition switch in on position, Fig. .
- Disconnect Tc within 3-10 seconds after DTC output begins.
- Supplemental Restraint System (SRS) warning lamps will illuminate three seconds later. Within 2-4 seconds, connect terminals Tc and CG of DLC3.
- SRS warning lamp will go off within 2-4 secon...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from 1990+.
Scion -> Anti-Lock Brake System (ABS)/Dynamic Control System Warning Lamp ->
Vehicle: 2008 Scion TC 2.4 L4 GAS
- Place ignition switch in on position.
- Connect jumper tool No. 09843-18040, or equivalent, to terminals TC and CG of diagnostic connector link, Fig. . Vehicle must be stopped at this time.
- Clear diagnostic trouble codes fr...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from 1990+.
Scion -> Malfunction Indicator Lamp (MIL) ->
Vehicle: 2008 Scion TC 2.4 L4 GAS
The MIL will also illuminate if the fuel tank filler cap is not properly tightened. Tighten fuel tank filler cap until it clicks.
If a misfire condition which may cause damage to the catalytic converter is present, the Check engine lamp will flash once per second until vehicle operation is outside the speed and load range causing the misfire. The lamp will stop flashing and remain steady
The MIL should light when the ignition switch is placed in the on position without starting the engine. When the engine is started, the lamp should go out. If it remains lit, a malfunction has been detected by t...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from 1990+.
Scion -> Anti-Lock Brake System (ABS)/Dynamic Control System Warning Lamp ->
Vehicle: 2008 Scion TC Spec 2.4 L4 GAS
- Place ignition switch in on position.
- Connect jumper tool No. 09843-18040, or equivalent, to terminals TC and CG of diagnostic connector link, Fig. . Vehicle must be stopped at this time.
- Clear diagnostic trouble codes fr...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Scion TC AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2008 Scion TC cars and light trucks sold in the U.S. from 1990+.
Scion -> Air Bag Warning Lamp ->
Vehicle: 2008 Scion TC Spec 2.4 L4 GAS
- Connect two service wires to terminals Tc and CG of DLC3 (Data Link Connector), then place ignition switch in on position, Fig. .
- Disconnect Tc within 3-10 seconds after DTC output begins.
- Supplemental Restraint System (SRS) warning lamps will illuminate three seconds later. Within 2-4 seconds, connect terminals Tc and CG of DLC3.
- SRS warning lamp will go off within 2-4 secon...
CLICK HERE TO GET FULL ACCESS TO 2008 Scion TC MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Scion TC vehicle. |
Access the Complete guide! |