Auto Parts Search
2008 Isuzu I-290 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Isuzu REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Isuzu I-290 AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2008 Isuzu I-290 S 2.9 L4 GAS
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove wheel drive shaft nut and washer. Discard wheel drive nut and replace with a new nut.
- Release wheel drive shaft by placing ...
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Isuzu I-290 AUTOMOBILES
Reset Procedures
Vehicle: 2008 Isuzu I-290 S 2.9 L4 GAS
The Low Tire Pressure warning lamp and/or the DIC (Driver Information Center) Low Tire Pressure message can be cl...
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2008 Isuzu I-290 AUTOMOBILES
Alternator, Replace
Vehicle: 2008 Isuzu I-290 S 2.9 L4 GAS
- Disconnect battery ground cable.
- Rotate or lift belt tensioner arm clockwise using a suitable tool to relieve tension from drive belt.
- Remove drive belt.
- Raise vehicle on lift.
- Remove lefthand front wheel.
- Remove push-pins securing lefthand wheel housing liner.
- Disconnect A/C compressor clutch connector.
- Remove A/C compressor mounting bolts. Remove two lower bolts and one upper bolt ONLY. Evacuation of A/C refrigerant is not required. One upper mounting bolt will secure A/C compressor.
- Lower vehicle to ground.
- Remove alternator electrical connector and terminal nut from back of alter...
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Isuzu I-290 AUTOMOBILES
Isuzu -> Intelligent Suspension Control (ISC) Indicator Lamp ->
Vehicle: 2008 Isuzu I-290 S 2.9 L4 GAS
The Intelligent Suspension Control (ISC) indicator lamp will illuminate when the ignition switch is placed in the on position and should go off when the engine is started. If the lamp remains on or comes on while driving, a fault in the Intelligent Suspension Control is present. After diagnosis and repairs, then DTCs may be cleared as follows:
- Connect a ju...
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2008 Isuzu I-290 AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2008 Isuzu I-290 S 2.9 L4 GAS
Inlet
- Disconnect negative cable from battery terminal.
- Drain engine coolant into a suitable container.
- Reposition hose clamp with suitable tool.
- Remove hose from heater core tube.
- Reposition hose clamp with suitable tool.
- Remove hose from inlet hose fitting at engine block.
- Reverse procedure to install.
Outlet
- Disconnect negative cable fro...
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2008 Isuzu I-290 AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2008 Isuzu I-290 S 2.9 L4 GAS
- Rotate or lift belt tensioner arm clockwise, using a suitable tool to relieve tension from dri...
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2008 Isuzu I-290 AUTOMOBILES
Component location diagrams for most 2008 Isuzu I-290 cars and light trucks sold in the U.S. from 1990+.
Rear Lighting Components Diagram for 2008 Isuzu I-290 S 2.9 L4 GAS Components on diagram: |
Body Components Diagram for 2008 Isuzu I-290 S 2.9 L4 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2008 Isuzu I-290 AUTOMOBILES
OEM drawn wiring diagrams for most 2008 Isuzu I-290 cars and light trucks sold in the U.S.
2008 Isuzu I-290 S 2.9 L4 GAS Wiring Diagram Components on diagram: |
2008 Isuzu I-290 S 2.9 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2008 Isuzu I-290 AUTOMOBILES
OEM TSB listings for most 2008 Isuzu I-290 cars and light trucks sold in the U.S. from 1985+.
Document: BATTERY DRAIN - REPROGRAM RADIO PRODUCT ENHANCEMENT PROGRAM Vehicle: 2008 Isuzu I-290 S 2.9 L4 GAS Symptoms: |
Document: WARRANTY PROCEDURES Vehicle: 2008 Isuzu I-290 S 2.9 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2008 Isuzu I-290 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2008 Isuzu I-290 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2008 Isuzu I-290 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2008 Isuzu I-290 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2008 Isuzu I-290 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2008 Isuzu I-290 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Isuzu I-290 vehicle. |
Access the Complete guide! |