Auto Parts Search
2008 Honda Odyssey CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Honda REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Honda Odyssey car and truck
repair procedures including Honda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Honda Odyssey automobile. Try the Automotix DIY solution today!
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Honda Odyssey AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2008 Honda Odyssey Touring 3.5 V6 GAS
- Loosen wheel nuts slightly.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Lift up locking tab on spindle nut then remove nut.
- Drain transmission fluid, then reinstall drain plug using new washer.
- Hold stabilizer ball joint pin with suitable tool and remove flange nut then separate from stabilizer link from lower arm.
- Remove lock pin from lower arm ball joint castle nut and remove nut then separate lower ball joint lower arm from using ball joint thread protector and remover.
- To avoid damaging ball joint, inst...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Honda Odyssey AUTOMOBILES
Component Replacement -> Installation -> Removal -> Tire Pressure Sensor -> TPMS Control Unit
Vehicle: 2008 Honda Odyssey Touring 3.5 V6 GAS
Tire Pressure Sensor
Removal
- Loosen the lug nuts.
- Raise and support vehicle with jack stands, then remove the wheel and tire assembly.
- Remove the valve cap and core.
- Deflate the tire completely.
- Remove any balance weights.
- Prior to dismounting the tire from the wheel, note the following precautions:
- Do outside of wheel first.
- Position the bead breaking fixture 90 degrees from the valve stem when separating the tire bead from the wheel, Fig. .
- Do not position the bead breaker of the tire changer too close to the rim.
- Position the wheel so the tire machine and tire iron are next to the...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2008 Honda Odyssey AUTOMOBILES
Starter, Replace
Vehicle: 2008 Honda Odyssey EX 3.5 V6 GAS
On models equipped with anti-lock codes for audio system, write down code for audio presets. When connecting battery ground cable upon installation you will need to enter the preset code. Ensure ignition switch is turned off.
- Disconnect battery cables. Remove battery ground cable first then remove other cable.
- Loosen breather pipe intake air cleaner clamps and remove air intake duct.
- Disconnect MAF/IAT sensor connectors.
- Remove air cleaner housing.
- Remove battery.
- Remove mounting base then remove battery base.
- Remove MAF/IAT wiring har...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2008 Honda Odyssey AUTOMOBILES
Cabin Air Filter Service -> Honda -> 2005-09 Odyssey
Vehicle: 2008 Honda Odyssey EX-L 3.5 V6 GAS
The cabin air filter should be replaced every 30,000 miles or 24 months. If the vehicle is operated primarily in urban areas with high concentrations of soot and diesel powered vehicles, replace the filter every 15,000 miles. The filter should be replaced more often if air flow is less than normal.
- While holding the lower glove compartment, release the damper, Fig. , then remove the glove compartment stop on each side.
- Remo...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Honda Odyssey AUTOMOBILES
Honda -> Automatic Transmission D, D4 Or D5 Indicator Lamp -> 2005-09 Odyssey
Vehicle: 2008 Honda Odyssey EX 3.5 V6 GAS
When the PCM detects an abnormal automatic transmission input or output signal the D lamp will usually blink and or the MIL will be illuminated. After completing diagnosis and repairs, reset the D and or MIL as follows:
- Wi...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2008 Honda Odyssey AUTOMOBILES
Heater Hose, Replace -> Bypass -> Inlet -> Outlet
Vehicle: 2008 Honda Odyssey Touring 3.5 V6 GAS
Inlet
- Disconnect negative cable from battery terminal.
- Drain engine coolant into a suitable container.
- Reposition hose clamp with suitable tool.
- Remove hose from heater core tube.
- Reposition hose clamp with suitable tool.
- Remove hose from water passage tube.
- Reverse procedure to install.
Outlet
- Disconnect negative cable from battery terminal.
- Drain engine coolant into a suitable container.
- Reposition hose clamp ...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2008 Honda Odyssey AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2008 Honda Odyssey LX 3.5 V6 GAS
- Rotate or lift belt tensioner arm, using a suitable wrench to relieve tension from drive belt. This is a hydraulic type a...
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2008 Honda Odyssey AUTOMOBILES
Component location diagrams for most 2008 Honda Odyssey cars and light trucks sold in the U.S. from 1990+.
 Engine Compartment Diagram for 2008 Honda Odyssey LX 3.5 V6 GASComponents on diagram: |
 Engine Compartment Wire Harness Diagram for 2008 Honda Odyssey Touring 3.5 V6 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2008 Honda Odyssey AUTOMOBILES
OEM drawn wiring diagrams for most 2008 Honda Odyssey cars and light trucks sold in the U.S.
 2008 Honda Odyssey EX-L 3.5 V6 GAS Wiring DiagramComponents on diagram: |
 2008 Honda Odyssey EX 3.5 V6 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2008 Honda Odyssey AUTOMOBILES
OEM TSB listings for most 2008 Honda Odyssey cars and light trucks sold in the U.S. from 1985+.
|
Document: ATEQ VT55 TPMS Update Information Vehicle: 2008 Honda Odyssey EX 3.5 V6 GAS Auto Systems: |
|
Document: Gap Between the Front Passengeraˆ™s Airbag Lid and the Dashboard Vehicle: 2008 Honda Odyssey EX 3.5 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2008 Honda Odyssey AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2008 Honda Odyssey cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2008 Honda Odyssey cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2008 Honda Odyssey cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2008 Honda Odyssey cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2008 Honda Odyssey SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Honda Odyssey vehicle.
|
| Access the Complete guide! |
