Auto Parts Search
We have info for following modifications of 2008 Cadillac SRX
- 2008 Cadillac SRX 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:A
- 2008 Cadillac SRX 3.6 V6 GAS, CID:217, Fuel Injection, Aspiration:217, Engine VIN:, Desg:7
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Cadillac SRX AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Cadillac SRX cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Lefthand -> Righthand
Vehicle: 2008 Cadillac SRX 4.6 V8 GAS
Lefthand
- Raise and support vehicle, then remove lefthand tire and wheel assembly.
- Remove mounting nut and separate outer tie rod from steering knuckles using steering linkage and tie rod puller tool No. J24319-B, or equivalent. Do not loosen tie rod end jam nut.
- Lock wheel hub and bearing from turning by installing suitable drift or punch into brake rotor against caliper mounting bracket.
- Remove and discard wheel drive shaft spindle nut.
- Disconnect wheel speed sensor connector and position wiring harness aside.
- Remove mounting nut and separate upper ball joint ball stud from kn...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac SRX DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Cadillac SRX AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Cadillac SRX cars and light trucks from 1990+.
DRIVESHAFT, Replace -> All Wheel Drive (AWD) -> Front -> Rear -> Rear Wheel Drive (RWD)
Vehicle: 2008 Cadillac SRX 3.6 V6 GAS
Front
- Raise and support vehicle.
- Remove mounting bolts and front propeller shaft Constant Velocity (CV) joint heat shield.
- Mark propeller shaft Constant Velocity (CV) joint to transfer case flange for installation alignment.
- Remove mounting bolts and disconnect CV joint from differential pinion flange by moving shaft rearward using suitable flat-bladed tool in differential flange notch.
- Remove mounting bolts and disconnect CV joint from transfer case flange by moving shaft forward using suitable flat-bladed tool in differential flange notch.
- Reverse procedure to install, noting th...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac SRX DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Cadillac SRX AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Cadillac SRX cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Lefthand -> Righthand
Vehicle: 2008 Cadillac SRX 3.6 V6 GAS
Lefthand
- Raise and support vehicle, then remove lefthand tire and wheel assembly.
- Remove mounting nut and separate outer tie rod from steering knuckles using steering linkage and tie rod puller tool No. J24319-B, or equivalent. Do not loosen tie rod end jam nut.
- Lock wheel hub and bearing from turning by installing suitable drift or punch into brake rotor against caliper mounting bracket.
- Remove and discard wheel drive shaft spindle nut.
- Disconnect wheel speed sensor connector and position wiring harness aside.
- Remove mounting nut and separate upper ball joint ball stud from kn...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac SRX DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Cadillac SRX AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Cadillac SRX cars and light trucks from 1990+.
DRIVESHAFT, Replace -> All Wheel Drive (AWD) -> Front -> Rear -> Rear Wheel Drive (RWD)
Vehicle: 2008 Cadillac SRX 4.6 V8 GAS
Front
- Raise and support vehicle.
- Remove mounting bolts and front propeller shaft Constant Velocity (CV) joint heat shield.
- Mark propeller shaft Constant Velocity (CV) joint to transfer case flange for installation alignment.
- Remove mounting bolts and disconnect CV joint from differential pinion flange by moving shaft rearward using suitable flat-bladed tool in differential flange notch.
- Remove mounting bolts and disconnect CV joint from transfer case flange by moving shaft forward using suitable flat-bladed tool in differential flange notch.
- Reverse procedure to install, noting th...
CLICK HERE TO GET FULL ACCESS TO 2008 Cadillac SRX DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Cadillac SRX vehicle. |
Access the Complete guide! |