Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Buick Enclave car and truck
repair procedures including Buick engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 Buick Enclave automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 Buick Enclave
- 2008 Buick Enclave CXL 3.6 V6 GAS, CID:217, Fuel Injection, Aspiration:217, Engine VIN:, Desg:7
- 2008 Buick Enclave CX 3.6 V6 GAS, CID:217, Fuel Injection, Aspiration:217, Engine VIN:, Desg:7
BRAKE SERVICE PROCEDURES FOR 2008 Buick Enclave AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Buick Enclave cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Bendix Master Cylinder -> Delco Master Cylinder -> Disassemble -> Wheel Cylinder
Vehicle: 2008 Buick Enclave CX 3.6 V6 GAS
Delco Master Cylinder
When performing the following procedures, refer to Fig. noting that the composite reservoir may vary in design.
Disassemble
- Remove master cylinder from vehicle.
- Remove reservoir cover and diaphragm. Discard old brake fluid in reservoir.
- Inspect cover and diaphragm. Replace if cut, cracked or deformed.
- Remove fluid level switch and proportioning valve assembly, if equipped.
- Depress primary piston and remove lock ring.
- Plug primary fluid outlet (outlet nearest to cowl when master cylinder is installed), then apply compressed air into secondary fluid outlet to remo...
CLICK HERE TO GET FULL ACCESS TO 2008 Buick Enclave BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Buick Enclave AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Buick Enclave cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Flush -> Manual Bleed -> Master Cylinder Bleed -> Parking Brake Bleed -> Pressure Bleed
Vehicle: 2008 Buick Enclave CXL 3.6 V6 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect and ...
CLICK HERE TO GET FULL ACCESS TO 2008 Buick Enclave BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Buick Enclave AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Buick Enclave cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Brake Pad Service
Vehicle: 2008 Buick Enclave CXL 3.6 V6 GAS
The procedures to remove and install the brake pads are outlined i...
CLICK HERE TO GET FULL ACCESS TO 2008 Buick Enclave BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Buick Enclave AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Buick Enclave cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Troubleshooting -> Brake Rattle -> Brake Roughness Or Chatter; Pedal Pumping -> Caliper Brake Fluid Leak -> Excessive Pedal Effort -> Excessive Pedal Travel -> Heavy Brake Drag -> No Braking Effect When Brake Pedal Is Depressed -> Pull, Uneven Or Grabbing Brakes -> Rear Brakes Locking On Application
Vehicle: 2008 Buick Enclave CX 3.6 V6 GAS
Excessive Pedal Travel
- Worn brake linings.
- Disc pads knock back after cornering or rough road travel.
- Piston and linings not properly seated or positioned.
- Insufficient fluid in system.
- Loose wheel bearing adjustment.
- Damaged or worn caliper piston seal.
- Improper booster pushrod adjustment.
- Pads out of flat more than .005 inch.
- Rear brake automatic adjusters inoperative.
- Improperly ground rear brake shoes.
Brake Roughness Or Chatter; Pedal Pumping
- Excessive lateral runout of rotor.
- Rotor excessively out of parallel.
Excessive Pedal Effort
- Frozen or seized pistons.
- Brake fluid, oil or grease on ...
CLICK HERE TO GET FULL ACCESS TO 2008 Buick Enclave BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Buick Enclave AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Buick Enclave cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Caliper Service -> Assemble -> Disassemble -> Inspection -> Installation -> Removal
Vehicle: 2008 Buick Enclave CX 3.6 V6 GAS
Removal
- Siphon 2/3 of the brake fluid from master cylinder.
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Compress caliper pistons until they bottom in bores using suitable clamp, Fig. .
- Disconnect brake hose at caliper by removing inlet fitting bolt.
- Remove mounting bolts and caliper.
Inspection
Should it become required to remove the caliper for installation of new components, clean components in denatured alcohol, wipe dry using lint-free cloths. Blow out drilled passages and holes using compressed air. Inspect dust boots for punctures or tears. If punctures or tears are...
CLICK HERE TO GET FULL ACCESS TO 2008 Buick Enclave BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Buick Enclave AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Buick Enclave cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Rotor, Replace -> 2WD Models -> 4WD Models -> Front -> Rear
Vehicle: 2008 Buick Enclave CX 3.6 V6 GAS
2WD Models
Front
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove caliper as outlined in .
- Remove grease cap from hub/rotor, Fig. .
- Remove cotter pin, nut and washer.
- Remove hub/rotor from spindle, being careful not to damage spindle threads or outer bearing.
- Reverse procedure to install, noting the following:
- Apply high-temperature wheel bearing grease to inner and outer wheel bearings.
- Torque nut to 12 ft. lbs., while turning wheel assembly forward by hand, back nut off one flat or until hole i...
CLICK HERE TO GET FULL ACCESS TO 2008 Buick Enclave BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Buick Enclave vehicle.
|
| Access the Complete guide! |
