Auto Parts Search
2007 Land Rover LR3 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Land Rover REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Land Rover LR3 AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2007 Land Rover LR3 SE 4.0 V6 GAS
Always remove the propeller shafts and viscous coupling as an assembly. Dismantling the individual units on the vehicle may cause damage to the components.
Never unbolt the viscous coupling support bearings from the body without first detaching the propeller shafts at the differential and IRD. The weight of the center section will pull the CV joint apart, causing irreparable damage.
Never allow the CV joint to be manipulated to an acute angle. This will cause the internal roller bearings to break up, leading to excessive backlash and CV joint failure.
- Raise vehicle on a four-po...
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2007 Land Rover LR3 AUTOMOBILES
Component Replacement -> Installation -> Removal -> Tire Pressure Sensor -> TPMS Front Antenna
Vehicle: 2007 Land Rover LR3 HSE 4.4 V8 GAS
Tire Pressure Sensor
Removal
- Loosen the wheel lug nuts.
- Raise and support the vehicle with jack stands, then remove the wheel and tire assembly.
- Remove the tire valve cap and core and release the air from the tire.
- Separate the bead on the inside and outside of the tire, note the following:
- The bead breaker tool should not be used within 12 inch of the sensor valve in either direction.
- Position the shoe of the tool between 2 to 4 inches away from the sensor valve.
- The lever and tire must not come in contact with the sensor.
- Remove the tire pressure sensor nut, then the sensor, Fig....
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2007 Land Rover LR3 AUTOMOBILES
Starter, Replace
Vehicle: 2007 Land Rover LR3 SE 4.4 V8 GAS
- Disconnect battery ground cable.
- Raise and support vehicle. Do not work on or under a vehicle supported only by a jack. Always support vehicle on safety stands.
- Remove front wheel.
- Remove bolts and engine undershield.
- Remove screw and engine compartment upper right heat shield.
- Remove three upper suspension arm and brake line heat shield nuts, bolts, and shields.
- Disconnect height sensor link arm.
- Remove stabilizer bar link nut. Use a wrench on hexagon provided to prevent ball joint rotating.
- Loosen upper arm retaining nut. To prevent wheel knuckle falling outwards and disconnection o...
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2007 Land Rover LR3 AUTOMOBILES
Cabin Air Filter Service -> Land Rover -> 2005-09 LR3 & 2006-09 Range Rover Sport
Vehicle: 2007 Land Rover LR3 HSE 4.4 V8 GAS
Under normal operating conditions the cabin air filter should be replaced every 12 months or 15,000 miles.
- Open the glove compartment.
- Release the glove compartment release latches, Fig. .
- Remove the cabin air filter cover, Fig. .
- Remove the cabin air filter e...
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2007 Land Rover LR3 AUTOMOBILES
Land Rover -> Dynamic Stability Control (DSC) Indicator Lamp ->
Vehicle: 2007 Land Rover LR3 SE 4.4 V8 GAS
The DSC warning lamp should light when the ignition switch is placed in the On position and go out when after the engine has been started. The DSC lamp will remain On with the engine started if the DSC switch has been pressed switching Off the DSC system but the traction control system is still active. The lamp will flash when ...
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2007 Land Rover LR3 AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2007 Land Rover LR3 SE 4.0 V6 GAS
Lower
- Drain coolant into a suitable container.
- Reposition hose clamp at radiator and remove hose.
- Reposition hose clamp at coolant pump and remove hose.
- Remove hose from vehicle.
- Reverse procedure to install.
...
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2007 Land Rover LR3 AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2007 Land Rover LR3 HSE 4.4 V8 GAS
- Disconnect battery ground cable.
- Loosen clip and disconnect air cleaner intake pipe.
- Disconnect mass air flow (MAF) sensor electrical connector.
- Remove air cleaner.
- Release coolant hose, unsnap three retaining clips, and remove cooling fan shroud.
- Remove ...
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 SERPENTINE BELT SERVICE PROCEDURES
WIRING DIAGRAMS FOR 2007 Land Rover LR3 AUTOMOBILES
OEM drawn wiring diagrams for most 2007 Land Rover LR3 cars and light trucks sold in the U.S.
2007 Land Rover LR3 HSE 4.4 V8 GAS Wiring Diagram Components on diagram: |
2007 Land Rover LR3 SE 4.4 V8 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2007 Land Rover LR3 AUTOMOBILES
OEM TSB listings for most 2007 Land Rover LR3 cars and light trucks sold in the U.S. from 1985+.
Document: Rear Differential Pinion Oil Seal Availability Vehicle: 2007 Land Rover LR3 SE 4.0 V6 GAS Auto Systems: |
Document: Driver Air Bag Module Trim Cover Distorted - Repair Procedure Vehicle: 2007 Land Rover LR3 SE 4.0 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2007 Land Rover LR3 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2007 Land Rover LR3 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2007 Land Rover LR3 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2007 Land Rover LR3 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2007 Land Rover LR3 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2007 Land Rover LR3 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2007 Land Rover LR3 vehicle. |
Access the Complete guide! |