Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 2004 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Acura RL cars and light trucks from 1990+.
Acura -> Hydraulic Brake Systems -> Brake System Bleed -> Anti-Lock Brake System (ABS) -> Conventional Brake System
Vehicle: 2004 Acura RL 3.5 V6 GAS
Conventional Brake System
- Fill master cylinder reservoir with brake fluid.
- Raise and support vehicle.
- Position drain pan under lefthand front wheel.
- Have an assistant depress brake pedal with slow, even pressure and hold it down. Only press pedal halfway to floor. Do not depress brake pedal to end of master cylinder stroke.
- Open bleed valve one full turn. Watch for air bubbles in fluid and listen for air escaping from system.
- With brake pedal still depressed, close bleeder valve.
- Have an assistant pump brake pedal several times. Do not depress brake pedal fully to end of master cyli...
CLICK HERE TO GET FULL ACCESS TO 2004 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Acura RL cars and light trucks from 1990+.
Acura -> Disc Brakes -> Rotor, Replace -> Front -> Rear
Vehicle: 2004 Acura RL 3.5 V6 GAS
Front
- Raise and support front of vehicle, then remove tire and wheel assemblies.
- Remove pin bolt and pivot caliper up away from rotor.
- Remove stud clips and slide rotor off hub.
- Reverse procedure to install.
Rear
- Raise and support rear of vehicle, then rem...
CLICK HERE TO GET FULL ACCESS TO 2004 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Acura RL cars and light trucks from 1990+.
Acura -> Power Brake Units -> Adjustments -> Brake Pedal Height -> Pushrod Clearance
Vehicle: 2004 Acura RL 3.5 V6 GAS
Brake Pedal Height
- Disconnect brake switch connector.
- Loosen brake switch locknut and back switch off until no longer touches brake pedal.
- Turn up floor mat and measure pedal height from lefthand center of pedal pad
- Loosen locknut and turn pushrod to specified height, Fig. .
- Torque locknut to 11 ft. lbs.
- On 3.2CL, 3.2TL and 3.2RL models, turn in brake light switch until plunger is fully depressed. Back switch off 1/4 turn to .01 inch clearance. Tighten locknut.
- On RL, RSX, TL, TSX and MDX models, turn in brake light switch until plunger is fully depressed. Turn switch 45º clockwise to lock...
CLICK HERE TO GET FULL ACCESS TO 2004 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Acura RL cars and light trucks from 1990+.
Acura -> Disc Brakes -> Brake System Bleed -> Anti-Lock Brake System (ABS) -> Conventional Brake System
Vehicle: 2004 Acura RL 3.5 V6 GAS
Conventional Brake System
- Fill master cylinder reservoir with brake fluid.
- Raise and support vehicle.
- Position drain pan under lefthand front wheel.
- Have an assistant depress brake pedal with slow, even pressure and hold it down. Only press pedal halfway to floor. Do not depress brake pedal to end of master cylinder stroke.
- Open bleed valve one full turn. Watch for air bubbles in fluid and listen for air escaping from system.
- With brake pedal still depressed, close bleeder valve.
- Have an assistant pump brake pedal several times. Do not depress brake pedal fully to end of master cyli...
CLICK HERE TO GET FULL ACCESS TO 2004 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Acura RL cars and light trucks from 1990+.
Acura -> Hydraulic Brake Systems -> Component Replacement -> Master Cylinder
Vehicle: 2004 Acura RL 3.5 V6 GAS
Master Cylinder
- On MDX models, remove intake air duct and throttle cable holder.
- On RL models, proceed as follows:
- Remove engine compartment covers.
- Remove mounting bolts and position underhood fuse/relay box aside.
- Remove mounting bolts, nuts and strut brace.
- On RSX models, remove air cleaner.
- On TL models, proceed as follows:
- Remove engine compartment covers.
- Remove mounting bolts and position underhood fuse/relay box aside.
- Remove mounting bolt and engine wire harness clamp from strut brace.
- Remove Accelerator Pedal Position (APP) sensor mounting bolt from strut brace.
- Remove mount...
CLICK HERE TO GET FULL ACCESS TO 2004 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2004 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2004 Acura RL cars and light trucks from 1990+.
Acura -> Power Brake Units -> Precautions -> Radio Coded Theft Protection System
Vehicle: 2004 Acura RL 3.5 V6 GAS
Radio Coded Theft Protection System
Anti-theft radios have a coded theft protection circuit. The security code number must be obtained before disconnecting battery, removing radio fuse or ...
CLICK HERE TO GET FULL ACCESS TO 2004 Acura RL BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2004 Acura RL vehicle. |
Access the Complete guide! |