Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 2003 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Infiniti I35 cars and light trucks from 1990+.
Infiniti -> Power Brake Units -> Power Brake Unit Service -> Overhaul -> Replacement
Vehicle: 2003 Infiniti I35 3.5 V6 GAS
Replacement
- Connect tube to any bleeder valve.
- Open bleeder valve, drain fluid by depressing brake pedal until master cylinder is empty.
- Repeat previous steps for second circuit.
- Remove brake line flare and master cylinder mounting nuts.
- Remove clevis pin, Fig. .
- Remove mounting nuts and brake booster.
- Reverse procedure to install noting the following:
- Inspect output ...
CLICK HERE TO GET FULL ACCESS TO 2003 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Infiniti I35 cars and light trucks from 1990+.
Infiniti -> Power Brake Units -> Description
Vehicle: 2003 Infiniti I35 3.5 V6 GAS
The vacuum assist diaphragm assembly multiplies the force exerted on the master cylinder piston in order to increase the hydraulic pressure delivered to the wheel calipers while decreasing the effort required to obtain acceptable stopping performance.
Vacuum assist units get their energy by opposing engine vacuum to atmospheric pressure. A piston, cylinder and f...
CLICK HERE TO GET FULL ACCESS TO 2003 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Infiniti I35 cars and light trucks from 1990+.
Infiniti -> Disc Brakes -> Rotor Replace -> Inspection -> Installation -> Removal
Vehicle: 2003 Infiniti I35 3.5 V6 GAS
Removal
- Raise and support vehicle, then remove wheels.
- Remove caliper mounting pins/bolts without disconnecting brake hose.
- On FX35, FX45, G35, M45, Q45 & QX56 models,if removing rear rotors, remove adjuster hole plug and back off parking brake shoe adjuster.
- On all models, free rotor from hub by tapping using suitable soft face driver.
- Remove ...
CLICK HERE TO GET FULL ACCESS TO 2003 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Infiniti I35 cars and light trucks from 1990+.
Infiniti -> Disc Brakes -> Brake System Bleed
Vehicle: 2003 Infiniti I35 3.5 V6 GAS
- Carefully monitor brake fluid level at master cylinder during bleeding procedure.
- Fill reservoir with new DOT 3 brake fluid.
- Ensure fluid level is full at all times.
- Connect transparent vinyl tube to air bleeder valve.
- Fully depress brake pedal several times.
- With brake pedal depressed, open air bleeder valve to release air.
- Close bleeder valve.
- Release brake pedal slowly.
- Repeat above steps until clear brake fluid comes out of air b...
CLICK HERE TO GET FULL ACCESS TO 2003 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Infiniti I35 cars and light trucks from 1990+.
Infiniti -> Power Brake Units -> Troubleshooting
Vehicle: 2003 Infiniti I35 3.5 V6 GAS
- With engine off, depress brake pedal several times. There should be no change in pedal stroke.
- With brake pedal depressed, start engine. Pedal should go down slightly.
- Run engine for two minutes, then turn engine off.
- Depress brake pedal slowly several t...
CLICK HERE TO GET FULL ACCESS TO 2003 Infiniti I35 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Infiniti I35 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Infiniti I35 cars and light trucks from 1990+.
Infiniti -> Hydraulic Brake Systems -> Component Service -> Assemble -> Disassemble -> Inspection -> Master Cylinder -> Proportioning Valve
Vehicle: 2003 Infiniti I35 3.5 V6 GAS
Master Cylinder
Refer to Figs. through for exploded view of master cylinder.
Disassemble
- Bend stopper cap claws outward.
- Lightly push piston into cylinder bore and remove valve stopper, Fig. .
- Remove pistons from master cylinder. If pistons are stuck in bore, apply air pressure.
- Remove reservoir tank.
Inspection
- Inspect master cylinder for scratches and pin holes.
- Inspect piston for deformation and scratches on piston cups.
- Inspect stopper cap excessive deformation of claws.
Assemble
- Install secondary and primary pistons in master ...
CLICK HERE TO GET FULL ACCESS TO 2003 Infiniti I35 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2003 Infiniti I35 vehicle. |
Access the Complete guide! |