Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2001 Isuzu Rodeo car and truck
repair procedures including Isuzu engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2001 Isuzu Rodeo automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2001 Isuzu Rodeo
- 2001 Isuzu Rodeo 2.2 L4 GAS, CC:2180, Fuel Injection, Engine VIN:, Desg:D
- 2001 Isuzu Rodeo 3.2 V6 GAS, CC:3165, Fuel Injection, Engine VIN:, Desg:W
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 Isuzu Rodeo cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2001 Isuzu Rodeo 3.2 V6 GAS
Front
- Place shift lever in neutral.
- Raise vehicle off ground and support it with safety stands in proper locations.
- Mark companion flange on front drive. Its recommended to use paint for reference marks. Never damage driveshaft flange and companion flange on front drive.
- Remove exhaust and transfer protectors.
- Remove bolts and then remove driveline from front final drive and transfer case.
- Reverse procedure to install noting the following:
- Torque driveline to transfer companion flange mounting bolts to 46 ...
CLICK HERE TO GET FULL ACCESS TO 2001 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 Isuzu Rodeo cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2001 Isuzu Rodeo 2.2 L4 GAS
Front
- Place shift lever in neutral.
- Raise vehicle off ground and support it with safety stands in proper locations.
- Mark companion flange on front drive. Its recommended to use paint for reference marks. Never damage driveshaft flange and companion flange on front drive.
- Remove exhaust and transfer protectors.
- Remove bolts and then remove driveline from front final drive and transfer case.
- Reverse procedure to install noting the following:
- Torque driveline to transfer companion flange mounting bolts to 46 ...
CLICK HERE TO GET FULL ACCESS TO 2001 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 Isuzu Rodeo cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2001 Isuzu Rodeo 3.2 V6 GAS
Front
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove four nuts and lockwashers.
- Remove snap ring and bearing cup.
- Break retainer ring with hammer...
CLICK HERE TO GET FULL ACCESS TO 2001 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 Isuzu Rodeo cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 2001 Isuzu Rodeo 3.2 V6 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped wit companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with a...
CLICK HERE TO GET FULL ACCESS TO 2001 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Isuzu Rodeo AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 Isuzu Rodeo cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2001 Isuzu Rodeo 2.2 L4 GAS
Front
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove four nuts and lockwashers.
- Remove snap ring and bearing cup.
- Break retainer ring with hammer...
CLICK HERE TO GET FULL ACCESS TO 2001 Isuzu Rodeo DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2001 Isuzu Rodeo vehicle.
|
| Access the Complete guide! |
