Auto Parts Search
We have info for following modifications of 2001 BMW Z3
- 2001 BMW Z3 Roadster 3.0 L6 GAS, CC:2979, Fuel Injection
- 2001 BMW Z3 Roadster 2.5 L6 GAS, CC:2494, CID:152, Fuel Injection, Aspiration:152
- 2001 BMW Z3 Coupe 3.0 L6 GAS, CC:2979, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 2001 BMW Z3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 BMW Z3 cars and light trucks from 1990+.
Anti-lock Brakes -> Description
Vehicle: 2001 BMW Z3 Roadster 3.0 L6 GAS
The Anti-Lock Brake System (ABS) consists of a control unit, hydraulic unit, speed sensors and wiring harness, Fig. . Each speed sensor has a gear wheel which runs past the permanently magnetized edge of the speed sensor installed in the wheel hub. The rotary motion of the wheels is recorded by inductive sensors and an electric signal is sent to the electronic control unit.
The electronic control unit is located in a compartment on the right side of the engine compartment. This control unit inputs acceleration, deceleration and slip factors from the electronic speed sensors, which ar...
CLICK HERE TO GET FULL ACCESS TO 2001 BMW Z3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 BMW Z3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 BMW Z3 cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Assemble -> Disassemble -> Front -> Inspection -> Overhaul -> Rear -> Replace
Vehicle: 2001 BMW Z3 Coupe 3.0 L6 GAS
Replace
Front
- Raise and support vehicle, then remove front tire and wheel.
- Press and hold brake pedal with suitable prop.
- Disconnect brake pipe from connection with hose.
- Remove wear indicator connector from lefthand side.
- Remove mounting bolts and caliper.
- Reverse procedure to install, noting the following:
- Bleed brake system.
- Ensure brake pad wear sensor wire does not contact rotor or wheel.
Rear
- Raise and support vehicle, then remove rear tire and wheel assembly.
- Drain moderate amount of brake fluid from reservoir using suitable syringe.
- Disconnect and plug caliper hydraulic line.
- Disconne...
CLICK HERE TO GET FULL ACCESS TO 2001 BMW Z3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 BMW Z3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 BMW Z3 cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting
Vehicle: 2001 BMW Z3 Roadster 3.0 L6 GAS
Refer t...
CLICK HERE TO GET FULL ACCESS TO 2001 BMW Z3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 BMW Z3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 BMW Z3 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 2001 BMW Z3 Roadster 2.5 L6 GAS
The following procedure has been revised by a Technical Service Bulletin.
Ensure traction control systems are turned Off prior to bleeding brake system.
- Connect suitable pressure bleeder to brake fluid reservoir. Maximum charging pressure is 43.5 psi.
- Attach bleeder hose and container to righthand rear wheel. Bleed until no bubbles appear.
- Repeat previous step for lefthand rear, righthand front and lefthand front wheels.
- Support rear suspension at wheel carriers and lower vehicle so rear suspension compresses to its normal loaded position (to prevent...
CLICK HERE TO GET FULL ACCESS TO 2001 BMW Z3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 BMW Z3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 BMW Z3 cars and light trucks from 1990+.
Disc Brakes -> Parking Brake Service
Vehicle: 2001 BMW Z3 Roadster 3.0 L6 GAS
- Remove brake disc as outlined in "Rotor, Replace."
- Remove parking brake shoes' return spring using suitable brake spring pliers,
- Turn retainers 90° and remove using retainer tool No. 34 4 000, or equivalent, Fig. .
- Remove shoes by rotating out...
CLICK HERE TO GET FULL ACCESS TO 2001 BMW Z3 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 BMW Z3 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 BMW Z3 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 2001 BMW Z3 Coupe 3.0 L6 GAS
The following procedure has been revised by a Technical Service Bulletin.
Ensure traction control systems are turned Off prior to bleeding brake system.
- Connect suitable pressure bleeder to brake fluid reservoir. Maximum charging pressure is 43.5 psi.
- Attach bleeder hose and container to righthand rear wheel. Bleed until no bubbles appear.
- Repeat previous step for lefthand rear, righthand front and lefthand front wheels.
- Support rear suspension at wheel carriers and lower vehicle so rear suspension compresses to its normal loaded position (to prevent...
CLICK HERE TO GET FULL ACCESS TO 2001 BMW Z3 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2001 BMW Z3 vehicle. |
Access the Complete guide! |