Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 2000 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 KIA Sephia cars and light trucks from 1990+.
Anti-lock Brakes -> Sephia & Spectra -> Diagnosis & Testing -> 1997 -> 1998-2002 -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation -> Intermittents -> Wiring Diagram
Vehicle: 2000 KIA Sephia 1.8 L4 GAS
Wiring Diagram
Refer to Figs. through for ABS wiring diagrams and to Fig. for ABS quick test.
Accessing Diagnostic Trouble Codes
1997
- Turn ignition Off.
- Locate Data Link Connector on rear firewall and connect a jumper wire between ABS output pin and G-2 pin, Fig. .
- Turn ignition On, then remove jumper wire.
- Study flashing pattern of ABS warning lamp and record code.
- Determine if there are additional DTCs stored by connecting jumper for at least three seconds and removing it.
- Study flashing pattern and record new DTC. Repeat previous step until all DTCs have been recorded.
- If there...
CLICK HERE TO GET FULL ACCESS TO 2000 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 KIA Sephia cars and light trucks from 1990+.
Anti-lock Brakes -> Sephia & Spectra -> System Service -> 1997 -> 1998-2002 -> ABS Control Unit -> Brake System Bleed -> Component Replacement -> Front Wheel Speed Sensor -> Hydraulic Control Unit (HCU) -> Pump Motor & Main Relays -> Rear Wheel Speed Sensors
Vehicle: 2000 KIA Sephia 1.8 L4 GAS
Brake System Bleed
Refer to "Hydraulic Brake Systems" for brake bleeding procedure.
Component Replacement
ABS Control Unit
1997
- Remove front passenger seat.
- Release ABS control unit electrical connector latch, then disconnect harness.
- Remove ABS control unit four mounting screws, then the unit.
- Reverse procedure to install, noting the following:
- Torque ABS control unit mounting screws to 108-144 inch lbs.
- Torque front passenger seat bolts to 32-36 ft. lbs.
Hydraulic Control Unit (HCU)
- Disconnect HCU electrical connector.
- Disconnect pump motor connector from relay.
- Tag their locations, then disco...
CLICK HERE TO GET FULL ACCESS TO 2000 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 KIA Sephia cars and light trucks from 1990+.
Drum Brakes -> Adjustments -> Brake Pedal -> Rio, Sephia & Spectra -> Sedona -> Sportage
Vehicle: 2000 KIA Sephia 1.8 L4 GAS
Brake Pedal
Rio, Sephia & Spectra
- On Rio models, distance from top center of brake pedal to floor mat should be 6.69-6.93 inches.
- On Sephia and Spectra models, distance from top center of brake pedal to floor mat should be 7.60-7.72 inches.
- On all models, disconnect brake pedal switch electrical connector (E), Fig. .
- Loosen locknuts (B) and turn switch (A) until it does not contact pedal.
- Loosen locknuts (D) and turn rod (C) to adjust height of brake pedal.
- Tighten brake pedal switch until plunger is completely compressed, then rotate additional 1/2 turn and tighten locknuts.
- Inspect operat...
CLICK HERE TO GET FULL ACCESS TO 2000 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 KIA Sephia cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Replacement
Vehicle: 2000 KIA Sephia 1.8 L4 GAS
Replacement
- Remove caliper in numbered sequence, Figs. , , and .
- R...
CLICK HERE TO GET FULL ACCESS TO 2000 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 KIA Sephia cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Brake Shoes, Replace -> Installation -> Removal -> Rio -> Sedona -> Sephia & Spectra -> Sportage
Vehicle: 2000 KIA Sephia 1.8 L4 GAS
Brake Shoes, Replace
Rio
- Remove brake shoes in numbered sequence, Fig. .
- Reverse procedure to install, noting the following:
- Clean backing plate with suitable vacuum cleaning equipment.
- Lubricate backing plate shoe contact pads.
- Tighten bolts and nuts to specifications.
Sedona
Removal
- Ensure parking brake is fully released.
- Raise and support vehicle.
- Remove tire and wheel.
- Remove brake drum to hub mounting screws, then the drum.
- Loosen parking brake cable square nut completely, Fig. .
- Remove adjuster spring from adjust lever and brake shoe, Fig. .
- Remove adjust lever, then rotate adjuster star...
CLICK HERE TO GET FULL ACCESS TO 2000 KIA Sephia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 KIA Sephia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 KIA Sephia cars and light trucks from 1990+.
Disc Brakes -> Rotor Replacement
Vehicle: 2000 KIA Sephia 1.8 L4 GAS
Replace rotor as...
CLICK HERE TO GET FULL ACCESS TO 2000 KIA Sephia BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2000 KIA Sephia vehicle. |
Access the Complete guide! |