Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Honda CR-V car and truck
repair procedures including Honda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Honda CR-V automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2000 Honda CR-V
- 2000 Honda CR-V EX 2.0 L4 GAS, CC:1972, Fuel Injection
- 2000 Honda CR-V LX 2.0 L4 GAS, CC:1972, Fuel Injection
- 2000 Honda CR-V SE 2.0 L4 GAS, CC:1972, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 2000 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Honda CR-V cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> 1997-2000 -> 1997-2001 -> 2002 -> Accord -> Accord & Odyssey -> Accumulator -> Accumulator Disposal -> Brake Fluid Change -> Brake System Bleed -> Civic -> Civic & CR-V -> Component Replacement -> Control Unit -> CR-V -> del Sol -> del Sol & Prelude -> Front -> Front Speed Sensor -> Modulator -> Odyssey -> Prelude -> Pulser & Sensor Gap Measurement -> Rear -> Rear Speed Sensor -> S2000 -> System Pressure Relief
Vehicle: 2000 Honda CR-V LX 2.0 L4 GAS
System Pressure Relief
Accord & Odyssey
- Remove bleeder cap from maintenance bleeder on modulator unit, then attach a suitable wrench to bleeder.
- Connect a rubber tube to bleeder and place other end in a container, Fig. .
- While holding tube in hand, loosen maintenance bleeder 1/8- 1/4 turn and collect fluid in container. Do not loosen bleeder too much; brake fluid is under high pressure and can burst out.
- Tighten maintenance bleeder to specification.
del Sol
- Drain brake fluid from master cylinder and modulator reservoir thoroughly as outlined under "Brake Fluid Change."
- Using bleeder t-wre...
CLICK HERE TO GET FULL ACCESS TO 2000 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Honda CR-V cars and light trucks from 1990+.
Anti-lock Brakes -> Diagnostic Chart Index
Vehicle: 2000 Honda CR-V SE 2.0 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 2000 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Honda CR-V cars and light trucks from 1990+.
Anti-lock Brakes -> Description -> Accumulator -> Control Unit -> Master Cylinder -> Modulator Unit -> Operation -> Power Unit -> Pressure Switch -> Speed Sensor -> System Components
Vehicle: 2000 Honda CR-V SE 2.0 L4 GAS
Operation
The anti-lock brake system (ABS) modulates the pressure of the brake fluid applied to each caliper. This prevents the wheels from locking, whenever they are likely to be locked due to excessive braking. It then restores normal hydraulic pressure when there is no longer any possibility of wheel locking. The system has a fail safe function that allows normal braking if there is a problem within the system.
[[table data]]System Components
Master Cylinder
A tandem master cylinder is used in order to improve safety of the braking system. In addition, a center valve method is introduced to match ...
CLICK HERE TO GET FULL ACCESS TO 2000 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Honda CR-V cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> Front -> Installation -> Rear -> Removal
Vehicle: 2000 Honda CR-V SE 2.0 L4 GAS
Front
Removal
- Refer to Figs. through when replacing brake pads.
- Raise and support front of vehicle, then remove wheel and tire assemblies.
- Remove brake hose clamp bolts from steering knuckle, Fig. .
- Remove caliper bolt, then swing caliper up out of the way.
- Remove shims, retainers and brake pads.
Installation
- Using vernier caliper, measure thickness of each pad lining. Compare measurement with specifications. If brake lining thickness is less than specified, replace both pads as a set.
- Clean caliper thoroughly, and check for grooves or cracks. Repair or replace as necessary.
- Install ...
CLICK HERE TO GET FULL ACCESS TO 2000 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Honda CR-V cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Inspection -> Installation -> Removal
Vehicle: 2000 Honda CR-V EX 2.0 L4 GAS
Removal
- Refer to Figs. through when replacing brake shoes.
- Raise and support rear of vehicle, then remove tire and wheel assemblies.
- Loosen parking brake, then remove rear brake drums.
- Remove tension pins by pushing retainer springs while turning.
- Lower brake shoe assembly being careful not to damage wheel cylinder dust cover, then remove lower return spring.
- Disconnect parking brake cable from parking brake lever, then remove brake shoe assembly.
- Remove upper return spring, self-adjuster lever and spring, then separate brake shoes.
- Remove wave washer, parking brake lever and pivot pin ...
CLICK HERE TO GET FULL ACCESS TO 2000 Honda CR-V BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Honda CR-V AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Honda CR-V cars and light trucks from 1990+.
Disc Brakes -> Description
Vehicle: 2000 Honda CR-V SE 2.0 L4 GAS
The caliper assembly consists of a pin slider caliper housing, inner and outer pad and lining assemblies and a single piston. The caliper slides on two pins which also act as attaching bolts between the caliper and caliper br...
CLICK HERE TO GET FULL ACCESS TO 2000 Honda CR-V BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2000 Honda CR-V vehicle.
|
| Access the Complete guide! |
