Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 2000 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Acura RL cars and light trucks from 1990+.
Anti-lock Brakes -> Precautions -> Radio Coded Theft Protection System
Vehicle: 2000 Acura RL 3.5 V6 GAS
Radio Coded Theft Protection System
Anti-theft radios have a coded theft protection circuit. The code number must be obtained before disconnecting the battery, removing radio fuse or remo...
CLICK HERE TO GET FULL ACCESS TO 2000 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Acura RL cars and light trucks from 1990+.
Disc Brakes -> Rotor, Replace
Vehicle: 2000 Acura RL 3.5 V6 GAS
- Raise and support front of vehicle, then remove tire and wheel assemblies.
- If replacing front rotor, remove pin bolt and pivot caliper up away from rotor.
- If replacing rear rotor, proceed as follows:
- Remove calip...
CLICK HERE TO GET FULL ACCESS TO 2000 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Acura RL cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Anti-Lock Brake (ALB) System -> Conventional Brake System
Vehicle: 2000 Acura RL 3.5 V6 GAS
Conventional Brake System
- Fill master cylinder reservoir with brake fluid.
- Raise and support vehicle.
- Position drain pan under righthand rear wheel.
- Have an assistant depress brake pedal with slow, even pressure and hold it down. Do not depress brake pedal to end of master cylinder stroke.
- Open bleed valve one full turn. Watch for air bubbles in fluid and listen for air escaping from system.
- With brake pedal still depressed, close bleeder valve.
- Have an assistant pump brake pedal several times. Do not depress brake pedal fully to end of master cylinder piston stroke.
- After bleeding ...
CLICK HERE TO GET FULL ACCESS TO 2000 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Acura RL cars and light trucks from 1990+.
Disc Brakes -> Adjustments -> Brake Pedal Height -> Parking Brake
Vehicle: 2000 Acura RL 3.5 V6 GAS
Brake Pedal Height
- Loosen locknut and back brake light switch off until it breaks contact with brake pedal.
- Loosen pushrod locknut, then turn pushrod in or out until to adjust pedal height to specifications, Fig. .
- Turn in brake light switch until plunger is fully depressed. Back switch off 1/4 turn and tighten locknut.
- With engine stopped, ensure brake pedal freeplay is within specifications, Fig. .
- Ensure brake lamps go out with brake pedal released.
Parking Brake
After servicing rear brakes, depress brake pedal sever...
CLICK HERE TO GET FULL ACCESS TO 2000 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Acura RL cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> Accumulator Pressure Switch -> Accumulator/Line Pressure Relief -> Brake System Bleed -> CL -> CL, RL & TL -> Component Replacement -> Control Unit -> Integra -> Modulator Unit Bleed -> Modulator Unit Fluid, Replace -> RL -> TL -> Wheel Sensor
Vehicle: 2000 Acura RL 3.5 V6 GAS
Brake System Bleed
Modulator Unit Fluid, Replace
CL, RL & TL
- Remove bleeder cap from the maintenance bleeder on modulator.
- Connect rubber hose to the maintenance bleeder, place other end in suitable container.
- Loosen maintenance bleeder 1/8 to 1/4 turn to collect fluid in container, Fig. . Do not loosen maintenance bleeder more than 1/4 turn, brake fluid is under high pressure.
- Tighten maintenance bleeder.
- Start engine and allow to idle for one minute, then check fluid level
- Repeat steps three through five several times in order to drain remaining fluid from modulator.
- Tighten maintenance...
CLICK HERE TO GET FULL ACCESS TO 2000 Acura RL BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Acura RL AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Acura RL cars and light trucks from 1990+.
Disc Brakes -> Precautions -> Radio Coded Theft Protection System
Vehicle: 2000 Acura RL 3.5 V6 GAS
Radio Coded Theft Protection System
Anti-theft radios have a coded theft protection circuit. The security code number must be obtained before disconnecting battery, removing radio fuse or ...
CLICK HERE TO GET FULL ACCESS TO 2000 Acura RL BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2000 Acura RL vehicle. |
Access the Complete guide! |