Auto Parts Search
We have info for following modifications of 1998 Isuzu Amigo
- 1998 Isuzu Amigo 3.2 V6 GAS, CC:3165, Fuel Injection, Engine VIN:, Desg:W
- 1998 Isuzu Amigo 2.2 L4 GAS, CC:2180, Fuel Injection, Engine VIN:, Desg:D
BRAKE SERVICE PROCEDURES FOR 1998 Isuzu Amigo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Isuzu Amigo cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit Service
Vehicle: 1998 Isuzu Amigo 3.2 V6 GAS
- Disconnect brake pipes.
- Remove master cylinder as outlined in "Hydraulic Brake Systems."
- Remove vacuum hose.
- Disconnect yoke clevis from brake pedal.
- Remove vacuum booster reta...
CLICK HERE TO GET FULL ACCESS TO 1998 Isuzu Amigo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Isuzu Amigo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Isuzu Amigo cars and light trucks from 1990+.
Anti-lock Brakes -> Diagnosis & Testing -> 1997 Four Wheel Anti-Lock Brakes -> 1998-2001 Four Wheel Anti-Lock Brakes -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Clearing DTCs -> Diagnosis By Symptom -> Diagnostic Circuit Inspection -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation -> Less Tech 1 Scan Tool -> Less Tech 2 Scan Tool -> Pinout Tests -> Rear Wheel ABS -> Rodeo -> Self-Diagnosis -> Trooper -> Wiring Circuit -> Wiring Circuits -> Wiring Diagrams -> With Tech 1 Scan Tool -> With Tech 2 Scan Tool
Vehicle: 1998 Isuzu Amigo 3.2 V6 GAS
Some diagnostic procedures require that the ignition switch remain On for extended periods of time while tests are performed. Low battery voltage may result, causing erroneous voltage readings. If vehicle system voltage becomes low, it is advisable to connect a battery charger and apply a slow charge while testing.
Rear Wheel ABS
Self-Diagnosis
The RWAL system performs a self-check every time the ignition key is turned from Off to On position. The system inspection consists of the following:
- Inspects the rear anti-lock light by illuminating for approximately two seconds.
- Inspects...
CLICK HERE TO GET FULL ACCESS TO 1998 Isuzu Amigo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Isuzu Amigo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Isuzu Amigo cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> Accelerometer -> Amigo, Axiom & Rodeo -> Anti-Lock Hydraulic Valve -> Brake System Bleed -> Component Replacement -> Electronic Brake Control Module (EBCM) -> Electronic Hydraulic Control Unit (EHCU) -> Front -> G-Sensor -> Hydraulic Unit -> Isolation/Dump Valve -> Rear -> Rodeo -> Rodeo & Trooper w/Rear Wheel ABS -> Speed Sensor -> Trooper -> Trooper & VehiCROSS
Vehicle: 1998 Isuzu Amigo 2.2 L4 GAS
Brake System Bleed
Refer to "Hydraulic Brake System" for brake bleeding procedure.
Component Replacement
These components are non-serviceable and must be replaced as a unit, do not try to disassemble components.
Hydraulic Unit
Rodeo
- Perform gear tension relief procedure using a Tech 1 scan tool, or equivalent.
- Remove battery ground cable.
- Drain brake fluid in reservoir, master cylinder and hydraulic unit.
- Place shop towel beneath hydraulic modulator brake pipes to prevent brake fluid from contaminating motor pack or electrical connectors.
- Remove hydraulic unit attaching bolt, then the hydrau...
CLICK HERE TO GET FULL ACCESS TO 1998 Isuzu Amigo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Isuzu Amigo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Isuzu Amigo cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Front -> Installation -> Rear -> Removal -> Replacement -> Service
Vehicle: 1998 Isuzu Amigo 2.2 L4 GAS
Replacement
Front
Removal
- Perform steps one through three as outlined under " Brake Pad Service" procedure.
- Disconnect brake hose from caliper and cap openings in hose and caliper.
- Remove caliper from vehicle.
Installation
- Perform steps one through three as outlined under " Brake Pad Service" installation procedure.
- Connect brake hose to caliper, then bleed brake system.
- Install wheel assembly and lower vehicle.
Rear
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove bolt and gaskets, then remove flexible hose from caliper and cap or tape hose openings to prevent contamination of ...
CLICK HERE TO GET FULL ACCESS TO 1998 Isuzu Amigo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Isuzu Amigo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Isuzu Amigo cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 1998 Isuzu Amigo 3.2 V6 GAS
The booster is a tandem vacuum unit. In normal operating mode, with the brakes in the released position, the booster operates with vacuum on both sides of its diaphragms. When the brakes are applied, air at atmospheric pressure is admitted...
CLICK HERE TO GET FULL ACCESS TO 1998 Isuzu Amigo BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Isuzu Amigo AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Isuzu Amigo cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting
Vehicle: 1998 Isuzu Amigo 2.2 L4 GAS
Refer to "... "
CLICK HERE TO GET FULL ACCESS TO 1998 Isuzu Amigo BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1998 Isuzu Amigo vehicle. |
Access the Complete guide! |