Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1998 Acura SLX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Acura SLX cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> Front -> Rear
Vehicle: 1998 Acura SLX 3.5 V6 GAS
Front
- Raise and support front of vehicle, then remove tire and wheel assemblies.
- Remove pin bolt and pivot caliper up away from rotor.
- Remove brake pad shims and pads, Figs. through .
- Clean caliper and inspect for excessive wear or damage.
- Install pad retainers, shims and pads.
- Back out bleed screw and push in piston to allow caliper to fit over pads. Tighten bleed screw
- Pivot caliper into position, install pin bolt and tighten.
Rear
- Raise and support rear of vehicle, then remove tire and wheel assemblies.
- Remove caliper shield and release parking...
CLICK HERE TO GET FULL ACCESS TO 1998 Acura SLX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Acura SLX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Acura SLX cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service
Vehicle: 1998 Acura SLX 3.5 V6 GAS
Components are not designed to be rebuilt. If...
CLICK HERE TO GET FULL ACCESS TO 1998 Acura SLX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Acura SLX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Acura SLX cars and light trucks from 1990+.
Power Brake Units -> Diagnosis & Testing -> Check Valve Test -> Function Test -> Leak Test
Vehicle: 1998 Acura SLX 3.5 V6 GAS
Function Test
- With engine stopped, depress brake pedal several times.
- Depress pedal hard and hold for 15 seconds. If pedal sinks, master cylinder, brake line or brake caliper is faulty.
- With brake pedal depressed, start engine. If pedal sinks slightly, vacuum booster is operating. If pedal height does not vary, booster or check valve is faulty.
Leak Test
- With engine running, depress brake pedal and hold, then stop engine. If pedal height does not vary with brake pedal depr...
CLICK HERE TO GET FULL ACCESS TO 1998 Acura SLX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Acura SLX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Acura SLX cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Assemble & Installation -> Front -> Integra, RSX, 2.2CL, 2.3CL, 2.5TL, 3.0CL & 1997-98 3.2TL -> MDX, 3.2CL, 3.5RL & 1999-2002 3.2TL -> Rear -> Removal & Disassemble
Vehicle: 1998 Acura SLX 3.5 V6 GAS
Front
Removal & Disassemble
- Raise and support front of vehicle, then remove tire and wheel assemblies.
- Remove banjo bolt and disconnect brake line. Secure hose in raised position.
- Remove pin bolt and caliper, Figs. through .
- Remove pad spring.
- Position suitable block of wood or shop rag in caliper opposite piston.
- Remove piston by applying compressed air into fluid inlet port.
- Remove piston boot and seal.
Assemble & Installation
- Clean caliper bore and piston with brake fluid, then inspect for excessive wear or damage.
- Apply suitable grease and install new piston seal in cylinder groove.
- In...
CLICK HERE TO GET FULL ACCESS TO 1998 Acura SLX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Acura SLX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Acura SLX cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Anti-Lock Brake (ALB) System -> Conventional Brake System
Vehicle: 1998 Acura SLX 3.5 V6 GAS
Conventional Brake System
- Fill master cylinder reservoir with brake fluid.
- Raise and support vehicle.
- Position drain pan under righthand rear wheel.
- Have an assistant depress brake pedal with slow, even pressure and hold it down. Do not depress brake pedal to end of master cylinder stroke.
- Open bleed valve one full turn. Watch for air bubbles in fluid and listen for air escaping from system.
- With brake pedal still depressed, close bleeder valve.
- Have an assistant pump brake pedal several times. Do not depress brake pedal fully to end of master cylinder piston stroke.
- After bleeding ...
CLICK HERE TO GET FULL ACCESS TO 1998 Acura SLX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Acura SLX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Acura SLX cars and light trucks from 1990+.
Power Brake Units -> Adjustments -> Pushrod Clearance
Vehicle: 1998 Acura SLX 3.5 V6 GAS
Pushrod Clearance
Refer to "Hydrau... "
CLICK HERE TO GET FULL ACCESS TO 1998 Acura SLX BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1998 Acura SLX vehicle. |
Access the Complete guide! |