Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1997 Isuzu Hombre car and truck
repair procedures including Isuzu engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1997 Isuzu Hombre automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1997 Isuzu Hombre
- 1997 Isuzu Hombre 2.2 L4 GAS, CC:2180, Fuel Injection, Engine VIN:, Desg:4
- 1997 Isuzu Hombre 4.3 V6 GAS, CC:4294, Fuel Injection, Engine VIN:, Desg:X
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Hombre AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Hombre cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1997 Isuzu Hombre 2.2 L4 GAS
Front
- Place shift lever in neutral.
- Raise vehicle off ground and support it with safety stands in proper locations.
- Mark flange yoke on front drive. Its recommended to use paint for reference marks. Never damage driveshaft flange and companion flange on front drive.
- Remove driveshaft with center supporting bracket from crossmember and from transmission or transfer case.
- Reverse procedure to install noting the following:
- Torque driveline to center supporting bracket bolts and nuts to 50 ft. lbs.
- To...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Hombre DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Hombre AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Hombre cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 1997 Isuzu Hombre 4.3 V6 GAS
Front
- Place shift lever in neutral.
- Raise vehicle off ground and support it with safety stands in proper locations.
- Mark flange yoke on front drive. Its recommended to use paint for reference marks. Never damage driveshaft flange and companion flange on front drive.
- Remove driveshaft with center supporting bracket from crossmember and from transmission or transfer case.
- Reverse procedure to install noting the following:
- Torque driveline to center supporting bracket bolts and nuts to 50 ft. lbs.
- To...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Hombre DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Hombre AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Hombre cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Nylon Injected Ring Type -> Snap Ring Type
Vehicle: 1997 Isuzu Hombre 4.3 V6 GAS
Disassemble
Nylon Injected Ring Type
Never clamp driveline tubing in a vise. Clamping driveline tubing in a vise may dent or deform the driveline resulting in an imbalance or unsafe condition. Always clamp on one of the yokes and support shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage bushing or cut the lip seal.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Mark driveline shaft to show which end connects ...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Hombre DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 Isuzu Hombre AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 Isuzu Hombre cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Nylon Injected Ring Type -> Snap Ring Type
Vehicle: 1997 Isuzu Hombre 2.2 L4 GAS
Disassemble
Nylon Injected Ring Type
Never clamp driveline tubing in a vise. Clamping driveline tubing in a vise may dent or deform the driveline resulting in an imbalance or unsafe condition. Always clamp on one of the yokes and support shaft horizontally. Avoid damaging the slip yoke sealing surface. Nicks may damage bushing or cut the lip seal.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Mark driveline shaft to show which end connects ...
CLICK HERE TO GET FULL ACCESS TO 1997 Isuzu Hombre DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1997 Isuzu Hombre vehicle.
|
| Access the Complete guide! |
