Auto Parts Search
We have info for following modifications of 1997 BMW Z3
- 1997 BMW Z3 Roadster 1.9 L4 GAS, CC:1895, Fuel Injection
- 1997 BMW Z3 Roadster 2.8 L6 GAS, CC:2793, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 BMW Z3 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 BMW Z3 cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 1997 BMW Z3 Roadster 2.8 L6 GAS
Disassemble
- Raise and support vehicle.
- Remove complete propeller shaft.
- Remove hose clamp.
- Lift out circlip.
- Push back boot using a suitable tool.
- Pull off constant-velocity joint using a standard puller.
Assemble
- Fill new constant-velocity joint with 80 grams of suitable grease. Do not cant inner race and cage as balls would fall o...
CLICK HERE TO GET FULL ACCESS TO 1997 BMW Z3 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 BMW Z3 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 BMW Z3 cars and light trucks from 1990+.
DRIVESHAFT, Replace -> With rear constant velocity joint -> With slide
Vehicle: 1997 BMW Z3 Roadster 2.8 L6 GAS
With slide
Caution: Mark universal joint to drive flange of rear axle. This will eliminate complaints of droning.
- Raise and support vehicle.
- Remove complete exhaust system.
- Remove heat shield.
- Unscrew holders for exhaust suspension.
- Remove clamp.
- With joint disk, unscrew joint disk on transmission.
- With universal joint, unscrew universal joint on transmission.
- Release threaded bush with a suitable tool by a few turns.
- Unscrew universal joint on final drive.
- Unscrew center bearing.
- Kink propeller shaft downwards at center mount and in so doing detach from centering on manual transmission...
CLICK HERE TO GET FULL ACCESS TO 1997 BMW Z3 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1997 BMW Z3 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1997 BMW Z3 cars and light trucks from 1990+.
DRIVESHAFT, Replace -> With rear constant velocity joint -> With slide
Vehicle: 1997 BMW Z3 Roadster 1.9 L4 GAS
With slide
Caution: Mark universal joint to drive flange of rear axle. This will eliminate complaints of droning.
- Raise and support vehicle.
- Remove complete exhaust system.
- Remove heat shield.
- Unscrew holders for exhaust suspension.
- Remove clamp.
- With joint disk, unscrew joint disk on transmission.
- With universal joint, unscrew universal joint on transmission.
- Release threaded bush with a suitable tool by a few turns.
- Unscrew universal joint on final drive.
- Unscrew center bearing.
- Kink propeller shaft downwards at center mount and in so doing detach from centering on manual transmission...
CLICK HERE TO GET FULL ACCESS TO 1997 BMW Z3 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1997 BMW Z3 vehicle. |
Access the Complete guide! |