Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1996 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Infiniti G20 cars and light trucks from 1990+.
Disc Brakes -> Parking Brake Service -> Adjustment -> I30 -> Inspection -> J30 & Q45 -> Replacement
Vehicle: 1996 Infiniti G20 2.0 L4 GAS
I30
Replacement
Refer to Fig. when inspecting and removing the parking brake cable.
- Remove center console.
- Disconnect warning switch connector, Fig. .
- Remove bolts.
- Slacken off and remove adjusting nut.
- Remove parking brake cable lock plate, Fig. .
Inspection
Check for wear and damage at all connecting points and replace as necessary. Ensure warning lamp and switch are functioning properly.
Adjustment
- Loosen parking brake cable.
- Fully depress brake pedal five times.
- Adjust control lever by turning adjusting nut, Fig. .
- Pull control lever with 44 pounds of force a...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Infiniti G20 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 1996 Infiniti G20 2.0 L4 GAS
Do not spill brake fluid on painted surfaces, it may cause damage to the paint. If brake fluid is spilled, wash immediately with water.
- Place container under master cylinder to avoid spillage, then fill master cylinder with brake fluid.
- Connect hose to bleeder valves, then depress brake pedal several times.
- With pressure applied to pedal open bleeder valve to release air trapped in system.
- Close bleeder, then release pedal slowly.
- Repeat steps...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Infiniti G20 cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> Actuator -> Actuator Relays -> Brake System Bleed -> Component Replacement -> G20 -> J30 -> Speed Sensors
Vehicle: 1996 Infiniti G20 2.0 L4 GAS
Brake System Bleed
Refer to "Hydraulic Brake System" for procedure.
Component Replacement
Speed Sensors
When replacing speed sensors refer to Figs. through .
Actuator
- Drain brake fluid by attaching hose to each wheel cylinder, then open each bleeder valve while depressing brake pedal.
- Mark each brake pipe connector for proper installation.
- Disconnect electrical connector, brake pipes, then attaching nuts.
- Remove actuator.
- Reverse procedure to install noting the following:
- Start...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Infiniti G20 cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting
Vehicle: 1996 Infiniti G20 2.0 L4 GAS
Refer to Figs. and for system symptom charts...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Infiniti G20 cars and light trucks from 1990+.
Disc Brakes -> Rotor Replacement -> Except I30, J30 & Q45 Rear -> I30, J30 & Q45 Rear -> Inspection -> Installation -> Removal -> Runout -> Surface -> Thickness
Vehicle: 1996 Infiniti G20 2.0 L4 GAS
Except I30, J30 & Q45 Rear
Removal
- Raise and support vehicle, then remove wheels.
- Remove caliper without disconnecting brake hose as outlined under "Caliper Service."
- Tap rotor with a suitable soft face driver to free it from hub.
- Remove rotor from vehicle.
Inspection
Surface
Check rotor for roughness, cracks or chips.
Runout
- Secure rotor to wheel hub with two wheel lug nuts.
- Check runout using a suitable dial indicator.
- Refer to "Disc Brake Specifications" for maximum runout allowance.
Thickness
Refer to "Disc Brake Specifications" for minimum allowable thickness.
Installation
- Place rotor o...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti G20 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Infiniti G20 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Infiniti G20 cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> Front -> Rear
Vehicle: 1996 Infiniti G20 2.0 L4 GAS
Front
- Raise and support vehicle, then remove master cylinder cap.
- Disconnect speed sensor connector.
- Remove lower caliper mounting pin/bolt.
- Pivot caliper upwards, then remove pad retainers and inner and outer shims, Fig. .
- On Q45 models, remove brake pad wear sensor.
- On all models, remove brake pads.
- Compress caliper piston with suitable C-clamp.
- Reve...
CLICK HERE TO GET FULL ACCESS TO 1996 Infiniti G20 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1996 Infiniti G20 vehicle. |
Access the Complete guide! |