Auto Parts Search
We have info for following modifications of 1995 Buick Riviera
- 1995 Buick Riviera 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:K
- 1995 Buick Riviera 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:1
BRAKE SERVICE PROCEDURES FOR 1995 Buick Riviera AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Buick Riviera cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder
Vehicle: 1995 Buick Riviera 3.8 V6 GAS
Master Cylinder
- Disconnect wire connector from brake warning pressure switch, if equipped.
- Disconnect brake lines from master cylinder.
- Remove master cylinder mounting nuts, then the master cylinder.
- On models wi...
CLICK HERE TO GET FULL ACCESS TO 1995 Buick Riviera BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Buick Riviera AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Buick Riviera cars and light trucks from 1990+.
Disc Brakes -> AC-Delco Single Piston Rear Disc Brake (Type 2) -> Adjustments -> Parking Brake
Vehicle: 1995 Buick Riviera 3.8 V6 GAS
Parking Brake
- Cycle brake system as follows:
- Apply service brake with a pedal force of 150 lbs. and release.
- Fully apply parking brake using approximately 125 lbs. of force on final stroke, and release.
- Apply and release parking brake two additional times as described above.
- Check parking brake pedal assembly for full release by turning ignition on and inspecting brake warning light. Light should be off. If brake warning light is on and parking brake appears to be fully released, operate manual pedal release lever and pull downward on front park brake cable to remove slack from pedal ass...
CLICK HERE TO GET FULL ACCESS TO 1995 Buick Riviera BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Buick Riviera AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Buick Riviera cars and light trucks from 1990+.
Power Brake Units -> General Service
Vehicle: 1995 Buick Riviera 3.8 V6 GAS
Two basic types of power assist mechanisms are used: vacuum assist diaphragm assemblies, which use engine vacuum or, in some cases vacuum pressure developed by an external vacuum pump. The second type is a hydraulic pressure assist mechanism, which use pressure developed by an external pump (usually the power steering pump). Both systems act to increase the force exerted on the master cylinder piston by the operator. This in turn increases the hydraulic pressure delivered to the wheel cylinders, while decreasing driver effort necessary to obtain acceptable stopping performance.
V...
CLICK HERE TO GET FULL ACCESS TO 1995 Buick Riviera BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Buick Riviera AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Buick Riviera cars and light trucks from 1990+.
Disc Brakes -> AC-Delco Single Piston Front Disc Brake (Type 2) -> Caliper Service -> Caliper Assemble -> Caliper Disassemble -> Caliper Installation -> Caliper Removal
Vehicle: 1995 Buick Riviera 3.8 V6 GAS
Caliper Removal
- Remove approximately 2/3 of brake fluid from master cylinder.
- Raise and support front of vehicle, then remove wheel and tire assembly.
- Position suitable pliers over inboard pad and housing as shown in Fig. , and squeeze pliers to compress caliper piston.
- If caliper assembly is being removed for service, remove inlet fitting attaching bolt, copper washer, and inlet fitting from caliper housing. Plug opening in inlet fitting to prevent fluid loss and contamination. Do not crimp brake hose, as this may damage internal structure of hose. If only shoe and lining assemblie...
CLICK HERE TO GET FULL ACCESS TO 1995 Buick Riviera BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Buick Riviera AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Buick Riviera cars and light trucks from 1990+.
Disc Brakes -> AC-Delco Single Piston Rear Disc Brake (Type 2) -> Precautions
Vehicle: 1995 Buick Riviera 3.8 V6 GAS
- Grease or any other foreign material must be kept off the brake linings, caliper, surfaces of the disc and external surfaces of the hub, during service procedures. Handling the brake disc and caliper should be done in a way to avoid deformation of the disc and nicking or scratching brake linings.
- If inspection reveals rubber piston seals are worn or damaged, they should be replaced immediately.
- During removal and installation of a wheel assembly, exercise care so as not to interfere wi...
CLICK HERE TO GET FULL ACCESS TO 1995 Buick Riviera BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Buick Riviera AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1995 Buick Riviera cars and light trucks from 1990+.
Power Brake Units -> Precautions
Vehicle: 1995 Buick Riviera 3.8 V6 GAS
- After disassembling a power brake unit, soak all metal parts in solvent.
- Use only alcohol on parts containing rubber. After the parts have been thoroughly cleaned and rinsed in solvent, they should be rewashed in clean alcohol before assembling.
- Use compressed air...
CLICK HERE TO GET FULL ACCESS TO 1995 Buick Riviera BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1995 Buick Riviera vehicle. |
Access the Complete guide! |