Auto Parts Search
1995 BMW 318I CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT BMW REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1995 BMW 318I AUTOMOBILES
Computer Relearn Procedures -> BMW
Vehicle: 1995 BMW 318I 1.8 L4 GAS
Disconnect or replace DME control unit only when ignition switch is off. After renewed operation, neutral basic values are set in the control unit for idle and emission control. An...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 BMW 318I AUTOMOBILES
Disc Brakes -> Caliper Service -> Assemble -> Disassemble -> Front -> Inspection -> Overhaul -> Rear -> Replace
Vehicle: 1995 BMW 318I 1.8 L4 GAS
Replace
Front
- Raise and support vehicle, then remove front tire and wheel.
- Drain moderate amount of brake fluid from reservoir using suitable syringe.
- Disconnect caliper brake hose.
- Remove caliper bolts and disconnect brake pad wear sensor electrical connector.
- Remove caliper toward rear.
- Reverse procedure to install, noting the following:
- Tighten mounting bolts to specifications.
- Bleed brake system.
- Ensure brake pad wear sensor wire does not contact rotor or wheel.
Rear
- Raise and support vehicle, then remove rear tire and wheel assembly.
- Drain moderate amount of brake fluid from reservoir u...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1995 BMW 318I AUTOMOBILES
BMW -> Fuel Filter Replacement -> Except X3 & Z4 -> Fuel System Pressure Relief -> Models w/Fitting Or Union Bolt Connection -> Models w/Fuel Hose Connection -> Removal & Installation
Vehicle: 1995 BMW 318I 1.8 L4 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
After the battery has been disconnected and reconnected, some abnormal driveability symptoms may occur. The vehicle may need to be driven while it relearns its adaptive strategy.
Fuel System Pressure Relief
- Obtain the vehicle owner's radio theft protection code.
- Remove the fuel pump relay(s).
- Start the engine and allow it to stall.
- Crank engine for 10 seconds to ensure the fuel pressure has been...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1995 BMW 318I AUTOMOBILES
DRIVESHAFT, Replace -> With rear constant velocity joint -> With Slide
Vehicle: 1995 BMW 318I 1.8 L4 GAS
With Slide
Caution: Mark universal joint to drive flange of rear axle. This will eliminate complaints of droning.
- Raise and support vehicle.
- Remove complete exhaust system.
- Remove heat shield.
- Unscrew holders for exhaust suspension.
- Remove clamp.
- With joint disk, unscrew joint disk on transmission.
- With universal joint, unscrew universal joint on transmission.
- Release threaded bush with a suitable tool by a few turns.
- Unscrew universal joint on final drive.
- Unscrew center bearing.
- Kink propeller shaft downwards at center mount and in so doing detach from centering on manual transmissio...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1995 BMW 318I AUTOMOBILES
Alternator, Replace
Vehicle: 1995 BMW 318I 1.8 L4 GAS
- Read fault memory with a suitable scan tool.
- Disconnect battery ground wire.
- Remove air cleaner upper section with air flow sensor or air-mass flow sensor.
- Remove alternator drive belt.
- On models equipped with hydraulic drive belt tensioner, remove guide pulley.
- On all models, unfasten screw in upper ...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 1995 BMW 318I AUTOMOBILES
Cabin Air Filter Service -> BMW -> 1992-98 3 Series
Vehicle: 1995 BMW 318I 1.8 L4 GAS
Service interval is determined by the service indicator.
- Obtain the radio anti-theft code prior to disconnecting the battery ground cable.
- Disconnect the battery ground cable.
- On all models except convertible, disengage the two air nozzles (located above the glove compartment) at the top. Position the nozzles straight ahead, then remove the nozzles.
- On all models, remove the glove compartment retaining screws located at each side. On convertible models, the upper two screws are accessed through the air nozzle opening.
- Disconnect the glove compartment lamp.
- Remove the two lower glove ...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1995 BMW 318I AUTOMOBILES
BMW -> Check Engine Lamp -> Less OBD II
Vehicle: 1995 BMW 318I 1.8 L4 GAS
The Check Engine lamp will be illuminated when the ignition switch is in the On position and the engine is stopped. If the engine is started, the lamp should go out. If the lamp remains lit, a diagnostic troubl...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1995 BMW 318I AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 1995 BMW 318I 1.8 L4 GAS
Lower
- Drain coolant into a suitable container.
- Reposition hose clamp at radiator and remove hose.
- Reposition hose clamp at coolant pipe on left side of engine and remove hose.
- Remove hose from vehicle.
- Reverse pr...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1995 BMW 318I AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1995 BMW 318I 1.8 L4 GAS
If a belt has been contaminated with antifreeze or oil it should be replaced.
- Remove fan cowl by lifting out expansion rivets on both sides.
- Secure fan pulley with suitable securing tool, or equivalent, then remove fan. Fan has lefthand handed threads. Turn nut clockwise to remove.
- Loosen tensioner lock bolts, the...
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1995 BMW 318I AUTOMOBILES
Component location diagrams for most 1995 BMW 318I cars and light trucks sold in the U.S. from 1990+.
Evaporative Emission Valve, Fuel Pump & On-Board Computer Temperature Sensor Diagram for 1995 BMW 318I 1.8 L4 GAS Components on diagram: |
Check Control, Engine Control, Supplemental Restraint Control & Transmission Control Modules Diagram for 1995 BMW 318I 1.8 L4 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1995 BMW 318I AUTOMOBILES
OEM drawn wiring diagrams for most 1995 BMW 318I cars and light trucks sold in the U.S.
1995 BMW 318I 1.8 L4 GAS Wiring Diagram Components on diagram: |
1995 BMW 318I 1.8 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1995 BMW 318I AUTOMOBILES
OEM TSB listings for most 1995 BMW 318I cars and light trucks sold in the U.S. from 1985+.
Document: Tools and Equipment Vehicle: 1995 BMW 318I 1.8 L4 GAS Auto Systems: |
Document: Tools and Equipment Vehicle: 1995 BMW 318I 1.8 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1995 BMW 318I AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1995 BMW 318I cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1995 BMW 318I cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1995 BMW 318I cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1995 BMW 318I cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1995 BMW 318I SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1995 BMW 318I vehicle. |
Access the Complete guide! |